AMX AXB-DTMF+ instruction manual Timing System SendCommands

Page 14

Programming

Operative System Send_Commands (Cont.)

Command

Description

 

 

ON HOOK

Place AXB-DTMF+ on hook.

 

Default at reset = YES

 

Example:

 

SEND_COMMAND DTMF, 'ON HOOK'

 

Places the AXB-DTMF+ on hook.

 

 

Timing System Send_Commands

The following table lists the commands, which establish normal signal timing.

Changing default time values may inadvertently alter the operation of the AXB-

DTMF+. It is unnecessary to change most default values.

The commands are listed alphabetically by operation and include syntax, syntax descriptions, usage

examples, time increments, and reset default values.

Timing System Send_Commands

Command

Description

 

 

BLOCKRDET-XXX

For telephone lines with distinctive ring feature.

 

Time increment = 10 ms

 

Example:

 

SEND_COMMAND DTMF, 'BLOCKRDET-185'

 

Sets the time to ignore "sub rings " at 1.85 seconds (1850 ms).

 

 

FLASH TIME-XXX

Set time AXB-DTMF+ will go "on-hook" when Send_Command FLASH is

 

issued.

 

• Time increment = 10 ms

 

• Default at reset = 63

 

Example:

 

SEND_COMMAND DTMF, 'FLASH TIME-65'

 

Sets time AXB-DTMF+ will go "on-hook" when Send_Command FLASH is

 

issued for .65 seconds (650 ms).

 

 

INROFFMIN-XXX

Minimum time required for an incoming ring to be in the off

 

state to reset ring count on AXB-DTMF+.

 

• Time increment = 100 ms

 

• Default at reset = 45

 

Example:

 

SEND_COMMAND DTMF, 'INROFFMIN-55'

 

Sets minimum off state time for an incoming ring to 5.5 seconds (5500 ms).

 

 

LOSSLCMAX-XXX

The maximum time a loop current is off (used to detect other end hung up).

 

• Time increment = 10 ms

 

• Default at reset = 80

 

Example:

 

SEND_COMMAND DTMF, 'LOSSLCMAX-90'

 

Sets a .9 second (900 ms) maximum off time for a loop current.

 

 

 

10

AXB-DTMF+ DTMF+ Interface

 

 

 

Image 14
Contents AXB-DTMF+ AMX Limited Warranty and Disclaimer Table of Contents Table of Contents Specifications AXB-DTMF+ SpecificationsFront panel components FIG Rear panel componentsSetting the Internal Jumpers Auto Answer modePreparing captive wires Wiring the AXB-DTMF+Line Setting mode Wiring guidelinesAudio Out Connecting External Telephone LinesAudio Testing the AXB-DTMF+ Off-hook line and off-hook phone troubleshootingOperative System SendCommands SendCommandsOperative SendCommands Sendcommand DTMF, AUDOUT-ON Sendcommand DTMF, AUDIO-ONSendcommand DTMF, AUDOUT-OFF Sendcommand DTMF, AUTO-ONSendcommand DTMF, Flash Sendcommand DTMF, EXTEN-OFFSendcommand DTMF, EXTEN-ON Sendcommand DTMF, OFF HookTiming System SendCommands Timing System SendCommandsSendcommand DTMF, OBUOFFMIN-45 Sendcommand DTMF, LOSSLCMIN-15Sendcommand DTMF, OBUOFFMAX-65 Sendcommand DTMF, OBUONMAX-65Sendcommand DTMF, OREONMIN-20 Sendcommand DTMF, OREOFFMAX-45Sendcommand DTMF, OREOFFMIN-20 Sendcommand DTMF, ORIOFFMAX-50Sendcommand DTMF, PAUSE-25 Sendcommand DTMF, ORIONMAX-30Sendcommand DTMF, ORIONMIN-25 Sendcommand DTMF, ROHOFFMAX-65Fine Tuning SendCommands Fine Tuning SendCommandsDistinctive Ring Patterns and SendCommands DTMF+ distinctive ring default patterns and time valuesChanging a Default Ring Pattern Distinctive Ring SendCommands Distinctive Ring SendCommandsAxcess Program Example PYZ-XXXBusycount Number of Retries Or RINGING, Send This Is not the 7TH RETRY, Wait Operation Channel # Description on Indicates Channel CodesChannel Codes Minute after call termination Program Example for Caller ID Caller IDCaller ID Data String Description CLID-mmddhhii-nnnnnnnnnn-text,0Dtmf Card Defineprogram If FINDSTRINGDTMFBUFFER,CLID-,1 Start Programming AXB-DTMF+ DTMF+ Interface AMX,