AMX NXM Series manual Ctof, Cton

Page 27

 

NXC-IRS4 4-Port IR/S Control Card

 

NXC-IRS4 Send_Commands (Cont.)

 

 

Command

Description

 

 

CH

All channels below 100 are transmitted as two digits. If the IR code for ENTER

Send IR pulses for the

(function #21) is loaded, an Enter will follow the number. If the channel is

greater than or equal to (>=) 100, then IR function 127 or 20 (whichever exists)

selected a channel.

is generated for the one hundred digit. Uses 'CTON' and 'CTOF' times for pulse

 

 

times.

 

Syntax:

 

SEND_COMMAND <DEV>,"'CH',<Number>"

 

Variable:

 

channel number = 0 - 199.

 

Example:

 

SEND_COMMAND IR_1,"'CH',18"

 

The NXC-IRS4 performs the following:

 

• Transmits IR signals for 1 (IR code 11). The transmit time is set with the

 

CTON command.

 

• Waits until the time set with the CTOF command elapses.

 

• Transmits IR signals for 8 (IR code 18).

 

• Waits for the time set with the CTOF command elapses. If the IR code for

 

Enter (IR code 21) is programmed, the IRS4 performs the following steps.

 

• Transmits IR signals for Enter (IR code 21).

 

Waits for the time set with the CTOF command elapses.

 

 

CP

You can set the Pulse and Wait times with the 'CTON' and 'CTOF' commands.

Halt and Clear all active or

Syntax:

buffered IR commands, and

SEND_COMMAND <DEV>,"'CP',<code>"

then send a single IR pulse.

Variable:

 

 

code = IR port's channel value 0 - 252 (253 - 255 reserved).

 

Example:

 

SEND_COMMAND IR_1,"'CP',2"

 

Clears the active/buffered commands and pulses IR_1 port's channel 2.

 

 

CTOF

Off time settings are stored in non-volatile memory. This command sets the

Set the duration of the Off

delay time between pulses generated by the 'CH' or 'XCH' send commands in

tenths of seconds.

time (no signal) between IR

Syntax:

pulses for channel and IR

function transmissions.

SEND_COMMAND <DEV>,"'CTOF',<time>"

 

 

Variable:

 

time = 0 - 255. Given in 1/10ths of a second. Default is 5 (0.5 seconds).

 

Example:

 

SEND_COMMAND IR_1,"'CTOF',10"

 

Sets the Off time between each IR pulse to 1 second.

 

 

CTON

This command sets the pulse length for each pulse generated by the 'CH' or

Set the total time of IR pulses

'XCH' send commands in tenths of seconds.

transmitted and is stored in

Syntax:

non-volatile memory.

SEND_COMMAND <DEV>,"'CTON',<time>"

 

 

Variable:

 

time = 0 - 255. Given in 1/10ths of a second. Default is 5 (0.5 seconds).

 

Example:

 

SEND_COMMAND IR_1,"'CTON',20"

 

Sets the IR pulse duration to 2 seconds.

 

 

NetLinx Cardframe, Control Cards, and NetModules

21

 

 

Page 26 Page 28
Image 27
Page 26 Page 28
Contents NetLinx Cardframe Control Cards, NetModules AMX Limited Warranty and Disclaimer Termination Limited WarrantyLicense Grant Intellectual PropertyPage Table of Contents NXC-VAI4 Analog Voltage Control Card NXF CardFrame NXF CardFrame and NetModulesRear Panel Components NXF Cardframe SpecificationsNXF Cardframe Specifications Front Panel ComponentsPositio Value Structure DEVNumberportsystem NXS-NMS NetModules NXS-NMS NetModules SpecificationsInstalling Control Cards into an NXF CardFrame Page Specifications NXC-COM2 SpecificationsNXC-COM2 Dual COM Port Control Card NXC-COM2 Channel Assignment Pinouts and Wiring ConfigurationNXC-COM2 Pinouts NXC-COM2 Wiring Configuration NXC-COM2 Channel AssignmentNXC-COM2 Programming Information NXC-COM2 SendCommandsRxclr GET BaudHsoff HsonXoff SET BaudTset Baud TxclrXON NXC-COM2 SendString Escape SequencesCommand Description 27,20,1 Sendstring DEV,27,20,1Sendstring RS2321,27,20,1 Page NXC-I/O10 Input/Output Control Card NXC-I/O10 SpecificationsNXC-I/O10 Channel Assignments Pinouts, Signals, and I/O Mode FunctionsNXC-I/O10 Pinouts, Signals, and I/O Mode Functions Pin Signal SW mode Functions VO mode functionsOpen mode setting Setting the Switch/Voltage Mode JumpersSetting the Voltage Clamp Jumper +12V or Open VO voltage Mode settingPage NXC-IRS4 4-Port IR/S Control Card NXC-IRS4 SpecificationsPinouts, Signals, and Functions NXC-IRS4 Channel AssignmentsProgramming Information Cton CtofPOF GET ModeIroff PODPON PtofPton XCH SET ModeSET Input Link SET IO LinkXchm Sendcommand DEV,XCHM extended channel modeSendcommand IR1,XCHM Sendcommand IR1,XCHPage NXC-REL10 Channel Assignments NXC-REL10 SpecificationsNXC-REL10 Relay Control Card Pinouts and FunctionsNXC-REL10 Connections/Wiring NXC-VAI4 Analog Voltage Control Card NXC-VAI4 SpecificationsNXC-VAI4 Pinouts, Signals, and Functions Channel Assignments NXC-VAI4 Channel AssignmentsChannel State Function NXC-VAI4 Channel Assignments NXC-VAI4 Output Level Assignments NXC-VAI4 Output Level AssignmentsLeve Description l NXC-VAI4 SendCommands NXC-VAI4 Input Level AssignmentsNXC-VAI4 Input Level Assignments GAS Levon LevoffSendcommand DEV,P1L50% Sendcommand DEV,P1ENSendcommand DEV,P3EEU Sendcommand DEV,P3EIBSendcommand DEV,P7N5.023V Sendcommand DEV,PI/ONLEVEL ValueSendcommand DEV,P1N5.023V Sendcommand DEV,P1N-5.023VSendcommand DEV,PI/OZVOLTAGEHL Sendcommand DEV,PI/OXLEVEL ValueSendcommand DEV,P1X5.023V Sendcommand DEV,P7X5.023VPage NXC-VOL4 Specifications NXC-VOL4 Volume Control CardPin Signal Channel Balanced Function Unbalanced Function NXC-VOL4 Pinouts, Signals, and FunctionsPort Port 2 Description Channel NXC-VOL4 Connections/WiringNXC-VOL4 Channel Assignments NXC-VOL4 Channel Assignments per portCreatelevel DEV, Level, Value NXC-VOL4 LevelsNXC-VOL4 Levels PortSendcommand MYDEVICE,P0R50 NXC-VOL4 SendCommandsSendcommand MYDEVICE,P0L50% Sendcommand DEV,POutput ChannelRTimeUDPage NXC-VOL4 Volume Control Card Enter the Document Name Here It’s Your World Take Control

NXM Series specifications

The AMX NXM Series is a cutting-edge solution in the realm of digital signage and media management, designed to redefine how businesses and organizations communicate with their audiences. This series is known for its robust features, advanced technologies, and exceptional performance capabilities that cater to a wide range of applications.

One of the standout features of the AMX NXM Series is its seamless integration with various software platforms, enabling users to deploy, manage, and monitor digital signage content effortlessly. It supports a variety of media formats, ensuring flexibility in content delivery. Users can easily schedule and update content remotely, making it an ideal solution for dynamic environments that require frequent updates.

The AMX NXM Series is powered by advanced processing technologies that guarantee high-quality playback of videos and images. This ensures that visual content is displayed with stunning clarity and vibrant colors, creating an engaging experience for viewers. Furthermore, the system includes support for high-definition content and various aspect ratios, allowing for the optimization of visuals across different display types.

In terms of connectivity, the AMX NXM Series comes equipped with multiple input and output options, including HDMI, USB, and network ports. This versatility makes it compatible with a wide array of devices and networks, streamlining the setup process for users. Additionally, the series features robust security protocols to protect content and data, ensuring that only authorized personnel have access to critical system functions.

The user interface of the AMX NXM Series is intuitive and user-friendly, facilitating easy navigation and content management. Administrators can benefit from a centralized dashboard that provides real-time monitoring and reporting capabilities. This allows for the assessment of performance metrics and content effectiveness, further enhancing the overall user experience.

Durability is another critical characteristic of the AMX NXM Series, as it is designed to operate in various environments, from retail spaces to corporate settings. Its rugged build and efficient cooling systems ensure reliable performance, even in demanding conditions.

In conclusion, the AMX NXM Series stands out as a premier choice for organizations looking to elevate their digital signage capabilities. With its combination of advanced technology, flexible content management, and user-friendly design, it is poised to make a significant impact in the digital communication landscape. As businesses continue to seek innovative ways to engage their audiences, the AMX NXM Series emerges as a powerful tool for effective visual communication.
Top Page Image Contents