AMX NXM Series manual GET Mode, Iroff, Pod, Pof

Page 28

NXC-IRS4 4-Port IR/S Control Card

NXC-IRS4 Send_Commands (Cont.)

Command

Description

 

 

GET MODE

The port responds with: <port #> <mode>,<carrier>,<io link channel>.

Poll the IR/Serial port's

Syntax:

configuration parameters and

SEND_COMMAND <DEV>,"'GET MODE'"

report the active mode

Example:

settings to the device

 

requesting the information.

SEND_COMMAND IR_1,"'GET MODE"

 

The system could respond with:

 

PORT 4 IR,CARRIER,IO LINK 0

 

 

IROFF

Syntax:

Halt and Clear all active or

SEND_COMMAND <DEV>,"'IROFF'"

buffered IR commands being

Example:

output on the designated

SEND_COMMAND IR_1,"'IROFF"

port.

 

Immediately halts and clears all IR output signals on the IR_1 port.

 

 

POD

Channel 255 changes are enabled. This command is used in conjunction with

Disable previously active

the I/O Link command.

Syntax:

'PON' (power on) or 'POF'

(power off) command

SEND_COMMAND <DEV>,"'POD'"

settings.

Example:

 

 

SEND_COMMAND IR_1,"'POD"

 

Disables the 'PON' and 'POF' command settings on the IR_1 device.

 

 

POF

If at any time the IR sensor input reads that the device is ON (such as if

Turn OFF a device connected

someone turned it on manually at the front panel), IR function 28 (if available)

to an IR port based on the

or IR function 9 is automatically generated in an attempt to turn the device back

OFF. If three attempts fail, the IR port will continue executing commands in the

status of the corresponding

buffer.

I/O Link input.

If there are no commands in the buffer, the IR port will continue executing

 

 

commands in the buffer and trying to turn the device OFF until a 'PON' or 'POD'

 

command is received. If the IR port fails to turn the device OFF, a PUSH and

 

RELEASE is made on channel 254 to indicate a power failure error. You can

 

only use the 'PON' and 'POF' commands when an IR device has a linked

 

I/O channel. Channel 255 changes are disabled after receipt of this command.

 

You can only use the PON and POF commands when an IR device has a

 

linked I/O channel.

 

Syntax:

 

SEND_COMMAND <DEV>,"'POF'"

 

Example:

 

SEND_COMMAND IR_1,"'POF'"

 

Sends power down IR commands 28 (if present) or 9 to the IR_1 device.

22

NetLinx Cardframe, Control Cards, and NetModules

Page 27 Page 29
Image 28
Page 27 Page 29
Contents NetLinx Cardframe Control Cards, NetModules AMX Limited Warranty and Disclaimer Limited Warranty License GrantIntellectual Property TerminationPage Table of Contents NXC-VAI4 Analog Voltage Control Card NXF CardFrame and NetModules NXF CardFrameNXF Cardframe Specifications NXF Cardframe SpecificationsFront Panel Components Rear Panel ComponentsStructure DEV Positio ValueNumberportsystem NXS-NMS NetModules Specifications NXS-NMS NetModulesInstalling Control Cards into an NXF CardFrame Page NXC-COM2 Specifications SpecificationsNXC-COM2 Dual COM Port Control Card Pinouts and Wiring Configuration NXC-COM2 Pinouts NXC-COM2 Wiring ConfigurationNXC-COM2 Channel Assignment NXC-COM2 Channel AssignmentNXC-COM2 SendCommands NXC-COM2 Programming InformationGET Baud HsoffHson RxclrSET Baud Tset BaudTxclr XoffNXC-COM2 SendString Escape Sequences XONSendstring DEV,27,20,1 Command Description 27,20,1Sendstring RS2321,27,20,1 Page NXC-I/O10 Specifications NXC-I/O10 Input/Output Control CardPinouts, Signals, and I/O Mode Functions NXC-I/O10 Pinouts, Signals, and I/O Mode FunctionsPin Signal SW mode Functions VO mode functions NXC-I/O10 Channel AssignmentsSetting the Switch/Voltage Mode Jumpers Setting the Voltage Clamp Jumper +12V or OpenVO voltage Mode setting Open mode settingPage NXC-IRS4 Specifications NXC-IRS4 4-Port IR/S Control CardNXC-IRS4 Channel Assignments Pinouts, Signals, and FunctionsProgramming Information Ctof CtonGET Mode IroffPOD POFPtof PONPton SET Mode SET Input LinkSET IO Link XCHSendcommand DEV,XCHM extended channel mode Sendcommand IR1,XCHMSendcommand IR1,XCH XchmPage NXC-REL10 Specifications NXC-REL10 Relay Control CardPinouts and Functions NXC-REL10 Channel AssignmentsNXC-REL10 Connections/Wiring NXC-VAI4 Specifications NXC-VAI4 Analog Voltage Control CardNXC-VAI4 Pinouts, Signals, and Functions NXC-VAI4 Channel Assignments Channel AssignmentsChannel State Function NXC-VAI4 Channel Assignments NXC-VAI4 Output Level Assignments NXC-VAI4 Output Level AssignmentsLeve Description l NXC-VAI4 Input Level Assignments NXC-VAI4 SendCommandsNXC-VAI4 Input Level Assignments GAS Levoff LevonSendcommand DEV,P1EN Sendcommand DEV,P3EEUSendcommand DEV,P3EIB Sendcommand DEV,P1L50%Sendcommand DEV,PI/ONLEVEL Value Sendcommand DEV,P1N5.023VSendcommand DEV,P1N-5.023V Sendcommand DEV,P7N5.023VSendcommand DEV,PI/OXLEVEL Value Sendcommand DEV,P1X5.023VSendcommand DEV,P7X5.023V Sendcommand DEV,PI/OZVOLTAGEHLPage NXC-VOL4 Volume Control Card NXC-VOL4 SpecificationsNXC-VOL4 Pinouts, Signals, and Functions Pin Signal Channel Balanced Function Unbalanced FunctionNXC-VOL4 Connections/Wiring NXC-VOL4 Channel AssignmentsNXC-VOL4 Channel Assignments per port Port Port 2 Description ChannelNXC-VOL4 Levels NXC-VOL4 LevelsPort Createlevel DEV, Level, ValueNXC-VOL4 SendCommands Sendcommand MYDEVICE,P0L50%Sendcommand DEV,POutput ChannelRTimeUD Sendcommand MYDEVICE,P0R50Page NXC-VOL4 Volume Control Card Enter the Document Name Here It’s Your World Take Control

NXM Series specifications

The AMX NXM Series is a cutting-edge solution in the realm of digital signage and media management, designed to redefine how businesses and organizations communicate with their audiences. This series is known for its robust features, advanced technologies, and exceptional performance capabilities that cater to a wide range of applications.

One of the standout features of the AMX NXM Series is its seamless integration with various software platforms, enabling users to deploy, manage, and monitor digital signage content effortlessly. It supports a variety of media formats, ensuring flexibility in content delivery. Users can easily schedule and update content remotely, making it an ideal solution for dynamic environments that require frequent updates.

The AMX NXM Series is powered by advanced processing technologies that guarantee high-quality playback of videos and images. This ensures that visual content is displayed with stunning clarity and vibrant colors, creating an engaging experience for viewers. Furthermore, the system includes support for high-definition content and various aspect ratios, allowing for the optimization of visuals across different display types.

In terms of connectivity, the AMX NXM Series comes equipped with multiple input and output options, including HDMI, USB, and network ports. This versatility makes it compatible with a wide array of devices and networks, streamlining the setup process for users. Additionally, the series features robust security protocols to protect content and data, ensuring that only authorized personnel have access to critical system functions.

The user interface of the AMX NXM Series is intuitive and user-friendly, facilitating easy navigation and content management. Administrators can benefit from a centralized dashboard that provides real-time monitoring and reporting capabilities. This allows for the assessment of performance metrics and content effectiveness, further enhancing the overall user experience.

Durability is another critical characteristic of the AMX NXM Series, as it is designed to operate in various environments, from retail spaces to corporate settings. Its rugged build and efficient cooling systems ensure reliable performance, even in demanding conditions.

In conclusion, the AMX NXM Series stands out as a premier choice for organizations looking to elevate their digital signage capabilities. With its combination of advanced technology, flexible content management, and user-friendly design, it is poised to make a significant impact in the digital communication landscape. As businesses continue to seek innovative ways to engage their audiences, the AMX NXM Series emerges as a powerful tool for effective visual communication.
Top Page Image Contents