Loewe Connect 42 Full-HD+ 100 Eco standard, Premium mode, Shop mode, Energy efficiency

Initial installation

Explanations of the setting possibilities, including the upgradeable satellite reception:

Energy	Decide how energy efficiently you want to operate your
efficiency	TV set. The value for the contrast (and thus the brightness
	of the background lighting) is adapted and the automatic
	dimmer activated or deactivated (see page 22) depending
	on the presetting.
	Eco standard:
	The emphasis for home use is on low energy consump-
	tion. The automatic dimmer is activated.
	Premium mode:
	This mode optimises the settings to a brighter environ-
	ment at a higher energy consumption. The automatic
	dimmer is activated.
	Shop mode:
	The picture settings are aligned to operation in the presen-
	tation room. The automatic dimmer is deactivated. If the
	ambient brightness diminishes, the energy consumption
	is not reduced.
	The presetting can be changed later in the TV menu under
	Picture Picture adjustment Presettings (see page 22)
	or under Settings	Energy efficiency.
Location of	Select the country for country-specific pre-settings.
TV set	If UK or IRL is selected for the location of TV set, it is
	possible to activate MHEG-5 (UK Freeview) for the TV set.
	A dialogue appears, where you can confirm to set the
	operating software to the selected location.
	If Yes is selected and confirmed with OK, the TV set turns
	off and on again automatically. First installation starts
	again after activating the operation software.
	If MHEG-5 was activated, DVB-C and DVB-S can not be
	used anymore. Only terrestrial/cable and DVB-T stations
	are available.
Antenna	Antenna/cable (analogue): analogue stations via
selection	DVB-T:	cable/antenna
		digital terrestrial stations
	DVB-C:	digital stations via cable
	DVB-S (cable 1):	digital stations via satellite
	DVB-S (cable 2):	digital stations via satellite
Encrypted	You can state whether coded stations are to be searched
stations	for in the search/update. Select yes to save all found
	scrambled stations. However, these stations can only

be received in connection with a CA module and the appropriate Smart Card. Handling of the CA module is described on page 40.

If a CA module with a SmartCard is already plugged in for

the station search, all the stations which this module can Downloaded From TV-Manual.com Manuals

descramble are also saved when no is preset.

Logical In various countries, digital stations (DVB-T, DVB-C) are Channel transmitted with a preset channel number per station, Number known as “Logical Channel Numbers“ – “LCN“. In this case the preset channel numbers are adopted as station memory locations and the stations of the preferred signal source sorted according to LCN. There may be gaps in the

numbering of the station list depending on the LCN.

For TV sets with MHEG-5 software the stations are tied to “Logical Channel Numbers” – “LCN” and sorted from 1-799. Digital stations without “LCN” are stored from 800 onwards. Analogue stations are stored from 1001.

DVB-T:If you are using an active antenna, then select yes (5V) Antenna for the antenna power supply.

DVB-C:The conventional settings will be derived from the selec- Settings tion of set location. Only change this if you know other symbol rates and modulation types or if you have to spec- ify the network ID for your cable network (information available from your cable network provider). If you want to run the station search independently of the channel

grid, select frequency search for the search method.

DVB-S:State how (single satellite or type of satellite system) you Satellite receive which satellite(s). Ask your dealer if in doubt. system

High band Specify here whether the high band of the selected satel- lite is to be searched in addition to the low band.

LNC Normally, you do not need to change the values for high frequencies and low band, unless the LNC (LNB) of your satellite Low Band / system uses a different oscillator frequency (important High Band for the frequency display).

After you have made these settings, you should receive the picture and sound of the selected satellites (only with Astra1 and HOTBIRD).

Search If you want to run the station search independently of method the channel grid, select frequency search for the search

method.

Symbol rates The symbol rates are specified by the satellite provider

and do not normally need to be changed.

Favoured Select the signal source from a list, the station of which is signal source to be at the top of your station list (starting with station

slot 1).

Recordings with automatic time control (see page 54) are only possible for the respective first DVB signal source.

continued on next page ￿

13 -