D-Link DES-1200M manual Supplying Power, Connecting the Switch

Page 28

Supplying Power

The DES-1200M is equipped with a universal switching power supply that accepts AC input voltages from 100 to 240VAC and 50 to 60 Hz.

To supply power to your switch:

1.Plug the connector of the power cord into the power port on the rear panel of your switch.

2.Plug the other end of the power cord into an AC wall outlet.

3.Set the power switch to ON and verify that the Power LED is lit. If it is not, check the following:

The power switch is in the ON position.

The power cord is properly connected to the wall outlet and to the power connection on the switch.

The wall outlet is functional.

Note: Network cable segments can be connected or disconnected from the switch while the power is on, without interrupting the operation of the switch.

Connecting the Switch

You can connect your switch to network devices such as desktops and workgroups or to other hubs.

Before connecting your switch to a desktop or workgroup make sure that:

The 10Base-T twisted pair Ethernet cabling is Category 3 or above.

The 100Base-TX Fast Ethernet cabling is tested Category 5.

The 100Base-FX fiber cabling is 62.5/125 micron multimode fiber, or 9/125 micro single-mode fiber.

The 1000Base-SX/LX fiber cabling is 50/125, 62.5/125 multi- mode or 9/125 micron single-mode fiber.

24

Page 27 Page 29
Image 28
Page 27 Page 29
Contents DES-1200M Fast Ethernet Switch System User’s Guide Planning Your Installation Page Introduction Page Package Contents UnpackingDES-1200M Front and Rear Panels Front PanelPower Port Power port accepts the power plug Power Switch DIP Switch with Link Mode DES-128 8 Ports 10/100Base-TX Module FeaturesDES-128 8 ports 10/100Base-TX Module Dip switch location and mode settings DES-121T Gigabit 1000Base-T Switch Module Features DES-121T Gigabit 1000Base-T Switch ModuleLED Indicators Page DES-124F 4 Ports 100Base-FX Fiber Module Port 100Base-TX/FX Front ViewDES-124F 4 ports 100Base-FX Fiber Module Feature DES-121G/GL 1000Base-SX/LX Fiber Module Features DES-121G/GL 1000Base-SX/LX Fiber Module10Base-T Ethernet Network Guidelines 100Base-TX Fast Ethernet Network Guidelines100Base-FX Fast Ethernet Network Guidelines 1000BASE-SX and LX Network GuidelineExpanded Networks Network Planning10Base-T Networks Expanding your 10Base-T Network 100Base-TX NetworksCollapsed Backbone Link Expanding your 100Base-TX network ClassCollapsed backbones 100Base Solution Fileserver Link1000Base Solution Multi-port Bridge with High-Bandwidth BackboneUsed as a Multiport Bridge Installation Choosing a LocationAttaching self-adhesive feet for desktop installation Rack InstallationSupplying Power Connecting the SwitchModule Setup and Installation Handling the ModulesInstalling 10/100Base-TX Modules Installing the ModulesInstalling 100Base-FX Modules Installing 1000Base-SX/LX Modules Removing the ModulesPower Input Voltage Frequency DimensionsCompatibility with Ethernet Standards Environment Operating StoragePhysical Characteristics Appendix B. PIN Assignments Are shown below Page FCC Certifications CE Mark Warning Limited Warranty What You Must Do For Warranty Service Page Wichtige Sicherheitshinweise Trademarks Offices Link Europe Registration Card Page

DES-1200M specifications

The D-Link DES-1200M is a cost-effective and efficient solution designed for small to medium-sized businesses requiring reliable network performance. This 12-port Managed Ethernet switch offers a blend of performance and functionality, making it an essential component for robust network infrastructure.

One of the main features of the DES-1200M is its 12 10/100 Mbps Fast Ethernet ports. This ensures adequate data transfer rates needed for everyday networking tasks. The switch supports both store-and-forward switching and wire-speed forwarding, enhancing the overall network performance while minimizing packet loss.

In terms of management capabilities, the DES-1200M provides a web-based graphical interface and Simple Network Management Protocol (SNMP) support. This allows administrators to efficiently monitor and configure the switch settings, ensuring optimal performance and security. The switch also offers port mirroring and network monitoring features, assisting in troubleshooting and performance optimization.

Another standout feature is the support for VLANs, specifically 802.1Q tagging. This technology enables the segmentation of networks into logical groups, improving both security and performance by reducing broadcast traffic. In addition, the DES-1200M supports link aggregation, which allows multiple ports to work together, increasing bandwidth and providing redundancy in case of link failures.

Security is a crucial aspect, and the D-Link DES-1200M doesn't disappoint. It includes features such as IEEE 802.1X port-based network access control, which restricts access to authenticated users only, thus enhancing network security. The switch also supports port security, allowing network administrators to limit the number of MAC addresses that can be connected to each port.

Power over Ethernet (PoE) support further adds to the switch’s utility. By providing power to connected devices such as IP cameras and access points through the Ethernet cable, the DES-1200M eliminates the need for additional power sources, simplifying installation and reducing clutter.

Finally, the D-Link DES-1200M is designed with a sturdy metal chassis that ensures durability and reliability. Its compact design also allows for efficient space utilization, making it a practical choice for various deployment environments.

In summary, the D-Link DES-1200M managed switch offers excellent performance, extensive management features, robust security options, and PoE capabilities. This combination makes it an ideal choice for businesses looking to enhance their network infrastructure while maintaining cost-effectiveness.
Top Page Image Contents