D-Link DES-5016 manual Installing Optional Modules

Page 22

Fast Ethernet Switching System User’s Guide

Installing Optional Modules

The process for installing all optional modules is the same. You cannot change the position of the CPU module. It must remain in the CPU slot. The DES-5016 will not work unless the CPU module is installed in the CPU slot.

You can purchase optional modules separately in order to meet the needs of your network. The two optional modules available for the DES-5016 are: a 2-Port 100BASE- FX (fiber optic) module and a 1-Port 1000BASE-SX (gigabit) module. As shown in Figure 10, optional modules can only be installed in Slot 3. Nothing can be installed in slot 4. The procedure for installing optional modules is the same for all three models.

Follow these steps to install the optional modules:

1.Power the DES-5016 off before installing the optional module. The optional modules are not hot swappable.

2.Grasp the thumbscrews on the sides of the optional module or blank bracket and turn counterclockwise to unscrew them. You can also use a screwdriver. Remove the old module or the blank bracket, as shown in Figure 9, and set aside. Do not discard the module or blank bracket. Put the module or blank bracket back in if you remove the new module.

3.Install the new module by inserting it into the guides, see Figure 10, and sliding it in until it stops. Press in firmly until you feel the module snap into place. The optional module should be level and flush with the rest of the DES-5016. Never force, twist or bend the optional module. The optional module slides in smoothly.

4.Gently push the thumbscrews in and turn clockwise to tighten. Do not over tighten the thumbscrews.

5.Power the DES-5016 on after you have installed the new module. The DES-5016 will auto detect the new module.

6.Remove the dust cover from the transceiver and plug the cable in, if you are installing a fiber optic or gigabit module.

7.Check the LEDs to verify that there is a link and a proper connection at the port.

See the Troubleshooting section if the optional module is not working properly.

Installing the DES-5016

14

Image 22

Contents DES-5016 Fast Ethernet Switching System User’s Guide Link Limited Warranty Hardware SoftwareNorth, Central, and South America Link Offices for Registration and Warranty ServiceEurope and Israel Copyright Statement Wichtige Sicherheitshinweise Table of Contents Page Page Audience About This GuideOrganization Features IntroductionPage Front Panel DES-5016TXDES-5016TF DES-5016TFRear Panel DES-5016 Rear PanelLocal Console Management Management MethodsUpdating Firmware Telnet ManagementInstalling the DES-5016 Unpacking the DES-5016Installation Options Desktop/ Shelf Installation Install Feet on BottomAttach Feet Rack Installation Attach Mounting BracketsInsert into Rack Installing Optional Modules Remove Blank Bracket Insert Optional Module Power On Cable Specifications Connecting the DES-5016 to the NetworkCopper Cable Cable Diagram Fiber Optic Cable Fiber Optic Ports PortsMDI-X Ports RS-232 PortConnecting the DES-5016 to other Switches and Hubs DES-5016 to DES-5016 ConnectionLEDs DES-5016TF LEDsCPU Module PowerDiagnostic StatusLED Act Port TX ModuleLink 100/10Port TX Module LEDs Port FX Module Link/ ActPort 100BASE-FX Module ColLit Dark Port 1000BASE-SX Module Gigabit Module LEDManaging the DES-5016 Local Console Management ∙ Data bits ∙ Parity None ∙ Stop bits ∙ Flow Control NoneTelnet ∙ Default User Name D-Link ∙ Default Password D-Link LogHelp Message Help MessagePanel Conventions Spacebar100BASE-FX/ 1000BASE-SX Switch Port Module System ConfigurationSwitch Port 1-8, 9-16 and Optional Module Configuration Console ProgramVlan Port Management Spanning Tree ConfigurationSnmp Management Configuration Trunking Port ManagementFactory Reset to Default Config Values System Configuration MenuSystem Reset System InformationSystem Information Menu Software UpdateBoot Prom Firmware Version Hardware RevisionSystem Description LAN Default GatewayMAC Address System NameSystem Reset System ResetFactory Reset Factory ResetFactory Reset Confirmation Advantages of Store and Forward System Rate ControlDisadvantages of Store and Forward Advantages of Cut-Through Disadvantages of Cut-ThroughSoftware Update Menu Software Update menuTransfer Firmware Xmodem User Account Management User Account Change MenuAccess Level PasswordConfirm Password Create New UserPage Status Delete UsersDelete Page Old Password Change PasswordNew Password Page Switch Port Configuration State Switch Port Configuration MenuPhysical Priority Port StateFlow Control Spanning Tree Configuration Menu Spanning Tree ConfigurationSTA Operation Levels Bridge Priority Forward Delay TimeSpanning Tree Algorithm Root CostRoot Bridge Root PortSnmp Management Configuration Access Right Snmp Management Configuration MenuSnmp Manager Setting Snmp Community StringCold Start Snmp Trap Manager SettingAuthentication Failure Link Change EventPage Vlan Port Management Vlan Port Management Menu Vlan Port Management menuPort # Create New VlanNew Vlan Name TrunkGroupPage Delete Vlan Menu Vlan NameModify Vlan Menu Virtual LAN NameTrunking Port Management Menu Trunking Port Management menuNew Trunking Group Name Create New Trunking PortName Page Trunking Port Delete Trunking PortModify Trunking Port Trunking Port Name Modify Trunking PortCables TroubleshootingProblem Solution Post Errors Port StatesPage Diagnostic LED Switch Specifications Appendix a DES-5016 Technical SpecificationsPort Specifications Page Fast Ethernet Switching System User’s Guide General EMI Fast Ethernet Switching System User’s Guide Performance Index ActUser Name 52, 54