Allied Telesis AT-8624T/2M, AT-8624POE Connecting the Switch, Using the CLI to configure a switch

Page 11

10

AT-8600 Series Switch

Connecting the Switch

Some configuration is necessary to enable the switch’s advanced switching capabilities. This is achieved via the Command Line Interface (CLI). On the AT-8624T/2M, you can also use the Graphical User Interface (GUI).

Using the CLI to configure a switch

1.Connect a terminal or PC to the terminal port (ASYN0).

Using the supplied RS-232 DB9 serial straight-through cable, connect your terminal or PC to the RS-232 port:

For the AT-8624T/2M and AT-8624PoE, the RS-232 port is on the front panel.

For the AT-8648T/2SP, the RS-232 port is on the back panel.

2.Set the communication parameters on your terminal or terminal emulation program to:

Bit rate: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

3.Log in.

After the switch has booted, the login prompt appears. If it does not appear, press the Enter key several times.

When the switch starts for the first time, it automatically creates an account with manager privileges. The account has the login name manager and the password is friend.

At the login prompt, enter the login name and password:

Login: manager

Password: friend

The switch’s command prompt appears, and you can now use the CLI to configure the switch.

4.Change the password.

A manager account left with the default password is a serious security risk. Remember the new password as there is no way to retrieve it if it is lost.

To change the account password, use the set password command.

Image 11
Contents Installation and Safety Guide Installation & Safety Guide AT-8600 Series Switch Table of Contents Models Covered by this Guide Package ContentsSelecting a Site Before you begin Installing the SwitchProcedure AT-8624T/2M front and rear panel with AC power inlet AT-8624PoE front and rear panel with AC power inlet Using the CLI to configure a switch Connecting the SwitchUsing the GUI to configure the AT-8624T/2Mswitch User Name manager the default Password friend RPS FaultChecking LEDs MasterLink Status Off Link and Mode LEDs for the AT-8648T/2SP switch LED Obtaining Documentation and Resources Category Approval Agency and Requirement StandardsElectrical AC Mains Circuit Overloading SafetyElectrical Notices Gefahr Durch Blitzschlag SicherheitAchtung Gefährliche Spannung Vorsicht Rahmeneinbau VorsichtNetzsicherung ELEKTRISK-OVERBELASTNING AF Spændingskredsløbet SikkerhedFare Under Uvejr Lynaktivitet Elektrisk Klasse 1-UDSTYRElektrische Toestellen VAN Klasse VeiligheidGevaar Voor Blikseminslag Sécurité Équipement DE Classe 1 Électrique TurvallisuusSÄHKÖ-VAIHTORVIRTASÄHKÖPIIRIN Ylikuormitus Sähköön Liittyviä Huomautuksia Varoitus SähköiskuvaaraSalamaniskuvaara Sähkö Tyyppiluokan 1 LaitteetElettricità Dispositivi DI Classe Norme di SicurezzaPericolo DI Fulmini Precipitazioni TemporalescheElektrisk Type 1- Klasse Utstyr SikkerhetElektrisitet Fare for LynnedslagPerigo DE Choque Causado POR Raio SegurançaElektrisk Overbelastning PÅ AC Hovedkretsløp Elétrico Equipamentos do Tipo Classe Electrico Equipo DEL Tipo Clase SeguridadAvisos Electricos Advertencia Peligro DE Electrochoque Peligro DE RayosElektriskt TYP Klass 1 Utrustning SäkerhetTillkännagivanden Beträffande Elektricitetsrisk Fara FÖR BlixtnedslagAT-8600 Series Switch
Related manuals
Manual 36 pages 1.08 Kb