Linksys EZXS55W, FESWSK05 v3 manual Windows 2000 Installation & Setup, Overview

Page 17

Instant EtherFast® Series

10. Remove your Driver Disk and CD-ROM and click Yes to restart your PC.

Fast Ethernet Switched 10/100 Network In a Box

Windows 2000 Installation & Setup

11. Once your PC has rebooted, double-click the Network Neighborhood

icon on your desktop. Ensure that you have access to the network. If you

do, your card has been properly installed.

• If you need to install the TCP/IP protocol, refer to your system adminis-

trator or your Windows NT documentation. Linksys does not provide

technical support for the configuration or troubleshooting of the TCP/IP

Overview

After physically installing the EtherFast® 10/100 LAN Card in your computer, fol- low these instructions to install the net- work driver. The installation procedure for the network driver will depend on your current system configuration. If at any time during the installation you encounter problems, consult the Troubleshooting section.

Note: Prior to pro- ceeding, ensure that you are operating Windows 2000 with administrative rights.

If you log into Windows 2000 with- out administrative rights, you may run into problems during the instal- lation.

protocol

The Windows NT Installation and setup of the EtherFast® 10/100 LAN

Card is complete. Return now to the section called Installing the

Workgroup Switch to complete the installation of your Network In A Box.

Note: If you had previously installed any NT service packs, you must re-install them. Otherwise, you may receive Not Enough Service Storage Space errors in the Event Viewer.

Installing the LAN Card’s Driver

After physically installing the EtherFast® 10/100 LAN Card in your computer, follow these instructions to install the network driver.

1.Start your computer if you haven’t already done so. Log in with administrative rights if you are asked to.

2.Windows will display the Found New Hardware Wizard box. Click Next.

27

28

Image 17
Contents Fast Ethernet Switched 10/100 Network In a Box Copyright & Trademarks Table of Contents Introduction Linksys Fast Ethernet Switched 10/100 Network In a BoxPackage Contents EtherFast 10/100 LAN Card EtherFast 10/100 5-Port Workgroup SwitchPer port UplinkInstalling the LAN Card Installing the LAN Card & Cabling TheOv rviewEtherFast 10/100 5-Port Workgroup SwitchOverviewRemove your computers outside cover Once your EtherFast 10/100 LAN CardBe disabled Installing the Workgroup SwitchConnecting Your Hardware Together and Booting Up OverviewInstalling the Driver in Windows 95 Version B Installing the LAN Card’s Driver Installing the Drivers for WindowsInstant EtherFast Series Installing the NetworkLAN Card’sCard’sDriversDriver Installing the Drivers for Windows MillenniumInstalling NT Networking & the LAN Card Driver Windows NT 4.0 Installation & SetupLog into Windows NT as an administrator Click on the Select from list... button to select a LAN Card Page Instant EtherFast Series Instant EtherFast Series Windows 2000 Installation & Setup Instant EtherFast Series Configuring the LAN Card for Windows 95, 98, and Millennium Configuring the LAN CardClient for Microsoft Networks Installing a 3.12 Server Novell NetWare Server SetupInstalling a 4.x Server Installing a 5.x ServerTroubleshooting for Windows 95, 98 and Millennium TroubleshootingNetwork Neighborhood is Empty You receive Dhcp Errors in WindowsRunning the LAN Card’s Diagnostics Sharing Your Files and Printers AppendixOverview Enabling File Sharing Enabling Printer SharingNetWare portion of your Windows Networking setup is complete Installing the Driver in Windows 95 Version aStarting Over in Windows 95 , 98, and Millennium Windows 95, 98 or Millennium Client for Windows NTStarting Over in Windows 95, 98, Millennium or Instant EtherFast Series Starting Over in Windows Manually Installing the Network Components in Windows 95 About Wake-on-LAN Compatibility Click on Start, Settings, then Control PanelTesting a Link Change WOL PC Installing and Configuring Wake-On-LANAbout Plug-and-Play PCI Technology Sending a Magic PacketLinux, Open Source, and Beta Operating Systems GlossaryInstant EtherFast Series Specifications for EZXS55W ver SpecificationsSpecifications for LNE100 ver Environmental Warranty InformationContact Information Tech Support RMA Issues FaxSales Information Web FTP SiteCopyright 2001 Linksys, All Rights Reserved
Related manuals
Manual 10 pages 45.61 Kb

EZXS55W, FESWSK05 v3 specifications

The Linksys FESWSK05 v3 and the EZXS55W are both notable pieces of networking hardware designed to enhance connectivity in various environments, from small businesses to homes. These Ethernet switches offer crucial features that facilitate efficient data transfer and network management.

The Linksys FESWSK05 v3 is a 5-port Fast Ethernet switch, utilizing a non-blocking architecture that allows for full wire-speed performance. Each port supports 10/100Mbps connections, making it a versatile choice for environments requiring high-speed data transfer. The switch is designed with ease of use in mind; it features a plug-and-play setup, eliminating the need for complex configuration. This makes it suitable for users of all technical levels. Furthermore, it includes auto-sensing technology that detects the speed of connected devices and automatically adjusts to ensure optimal alignment.

The EZXS55W, on the other hand, is a smart switch with features that cater to growing networking demands. It also supports 5 ports, with similar 10/100Mbps capabilities, but offers additional functionalities, such as a built-in web management interface. This allows for advanced features like VLAN support and Quality of Service (QoS). These capabilities enable users to prioritize traffic for bandwidth-sensitive applications such as VoIP and video conferencing, ensuring a stable and reliable connection.

Both models support Auto-MDI/MDI-X functionality, which simplifies installation by automatically detecting and configuring the type of connection. This is particularly useful for network administrators managing multiple connections without the need for crossover cables. Additionally, they are equipped with IEEE 802.3, 802.3u, and 802.3x standards compliance, ensuring compatibility with a wide range of devices.

In terms of physical characteristics, the Linksys switches are compact and designed for desktop or wall-mounted installation, making them suitable for space-constrained environments. Their fanless design ensures silent operation, which is ideal for both home and office settings.

Overall, the Linksys FESWSK05 v3 and EZXS55W are excellent choices for users seeking reliable, efficient, and straightforward networking solutions. With their robust feature set and user-friendly design, they provide the necessary foundation for a well-functioning network, catering to the demands of modern connectivity. Whether for home use or in a small office, these switches deliver performance and reliability that users can count on.