Linksys EG24M manual Rack-Mounting the GigaSwitch, Powering On and Resetting the GigaSwitch

Page 7

Linksys EtherFast® II Series

Rack-Mounting the GigaSwitch

The 10/100 Managed 24-Port GigaSwitch can be used as a free-standing unit, or installed in any standard 19-inch rack.

Use the following instructions to rack-mount the GigaSwitch:

Before you begin, disconnect all cables from the GigaSwitch.

1.Place the GigaSwitch right side up, with the front panel facing you.

2.Position a mounting bracket over the screw holes on one side of the GigaSwitch.

3.Secure the mounting bracket by inserting three screws into the screw holes. Use a screwdriver to tighten the screws, ensuring that they are fastened firmly in place.

4.Repeat steps 2 and 3 to install the other mounting bracket on the opposite side of the GigaSwitch.

5.Insert the GigaSwitch into the 19-inch rack and secure it with suitable screws (not provided). Ensure that the ventilation holes are not obstructed.

The rack-mount installation is complete.

You can now re-connect the cables to the back of the GigaSwitch.

10/100 Managed 24-Port GigaSwitch

Powering On and Resetting the GigaSwitch

To power on the GigaSwitch, simply connect the AC power cord to the back of the GigaSwitch, then plug the power cord into an electrical outlet. The GigaSwitch will boot up within approximately 30 seconds.

If you need to reset the GigaSwitch, depress the RESET button (located on the rear of the switch) for approximately one or two seconds.

Uplinking the GigaSwitch

Port 24 on the EtherFast II 10/100 Managed 24-Port GigaSwitch can act as an uplink port, allowing you to uplink to other switches or hubs using a standard Ethernet connection.

To uplink the switch, connect one end of a Category 5 (or better) network cable into Port 24, then connect the other end of the cable into the desired network device’s uplink port. To enable uplinking capability, depress the MDI/MDIX button on the front of the switch.

Installing the Gigabit Expansion Modules

Use the following instructions to install the Gigabit Expansion Modules:

Before you begin power off the GigaSwitch by disconnecting all cables from the GigaSwitch.

1.Place the GigaSwitch right side up, with the rear panel facing you.

2.Use a screwdriver to remove the desired Expansion Module cover plate (labeled “Slot 1” and “Slot 2”). Set the screws aside for step 4.

3.Insert the Gigabit Expansion Module (must be purchased seperately) into the selected Gigabit Expansion Port, ensuring that it is seated firmly in place.

4.Secure the module in place using the screws and a screwdriver.

The Gigabit Expansion Module installation is complete.

You can now re-connect the cables to the back of the GigaSwitch.

6

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 10/100 Managed Port GigaSwitch Copyright & Trademarks Table of Contents Introduction Linksys EtherFast 10/100 Managed 24-Port GigaSwitchLEDs Getting to Know the GigaSwitchFull-Duplex Considerations Installing the GigaSwitchPositioning the GigaSwitch Fast Ethernet ConsiderationsInstalling the Gigabit Expansion Modules Rack-Mounting the GigaSwitchPowering On and Resetting the GigaSwitch Uplinking the GigaSwitchSwitch Management Basic Management Activities Configuring the GigaSwitchWeb-Based Configuration and Management Logging On to the GigaSwitchChanging the Location General Management ConfigurationChanging the Administration Password Changing the System NameStatistic Collection Changing the Guest PasswordReturning to the Basic Management Screen LAN Port ConfigurationReboot-on-Error Remote Telnet LoginChanging the Speed and Flow Control Setting the Line SpeedChanging the Flow Control Console Port ConfigurationDisplaying Physical Port Address Enabling or Disabling Modem Control Options Specifying a Modem Setup StringChanging the Console Baud Rate Selecting a Flow Control MethodSpecifying a Slip Address Enabling or Disabling SlipSpecifying a Slip Subnet Mask Advanced Management Activities Switching Database ConfigurationCreating a New Vlan Default VlanVlan Perspective Obtaining a Vlan PerspectiveAdding New Switch Ports Viewing Vlan Activities Deleting a Vlan IDScrolling Through Domains Viewing Vlan SettingsSearching for MAC Addresses Obtaining Additional InformationDeleting Ports Adding PortsMAC Address Perspective IP Multicast Group PerspectivePer Port Vlan Activities Port PerspectiveScrolling Through MAC Addresses Per Port Statistics IP NetworkingARP Table Settings IP & RIP SettingsAdding Static ARP Table Entries Searching for ARP Table Entries Deleting Static ARP Table EntriesRIP Routing TableVlan IcmpDeleting Routing Table Entries Dhcp Gateway SettingsSearching for Routing Table Entries Servers DelayRelays Ping Settings Bridging Static Filtering Spanning Tree Functions Spanning Tree Protocol ConfigurationsSpanning Tree Path Costs Spanning Tree Port StatesSnmp Functions Spanning Tree Port PrioritiesLinksys EtherFast II Series Port Trunking Other ProtocolsPort Mirroring Upgrading Firmware Snmp Agent and MIB-2 RFC1213 Snmp and Rmon ManagementRmon Groups Supported Rmon MIB RFC 1757 and Bridge MIB RFCBridge Groups Supported Fiber Optic Cabling AppendixAbout Fast Ethernet About Gigabit EthernetTwisted-Pair Cabling Crimping Your Own Network Cables Customer Support SpecificationsLinksys Warranty Information EnvironmentalT p / / w w w. l i n k s y s . c o m

EG24M specifications

The Linksys EG24M is a powerful and versatile network switch that caters to the needs of both small and medium-sized businesses. With its robust features and reliable performance, the EG24M has established itself as a go-to choice for enhancing network connectivity in diverse environments.

At the heart of the Linksys EG24M are 24 Ethernet ports, all of which support Gigabit speed. This allows for rapid data transfer rates, making it ideal for bandwidth-intensive applications such as video streaming, online gaming, and large file transfers. All ports are auto-sensing and configure themselves automatically to the speed of connected devices, optimizing performance without the need for manual configurations.

One of the standout features of the EG24M is its support for Power over Ethernet (PoE). This technology enables the switch to deliver electrical power along with data over standard Ethernet cables, eliminating the need for additional power supplies for PoE-enabled devices like IP cameras, VoIP phones, and wireless access points. This simplifies installation and reduces clutter, allowing for flexible deployments in various environments.

The Linksys EG24M also incorporates advanced Layer 2 switching capabilities. It supports features such as VLANs (Virtual Local Area Networks), allowing network segmentation to enhance security and traffic management. This is particularly beneficial in larger networks where different departments or functions require isolated communication channels. Additionally, the switch supports Quality of Service (QoS) features, enabling prioritization of critical network traffic to ensure smooth performance for essential applications.

Security is another key aspect of the Linksys EG24M. It has built-in features to protect the network against unauthorized access, ensuring that sensitive data remains secure. The switch also supports storm control and broadcast control to mitigate network congestion and enhance overall performance.

In terms of design, the EG24M features a compact and robust form factor, which makes it suitable for mounting in standard racks or desktop environments. Its fanless design ensures silent operation, making it ideal for office use where noise can be a distraction.

In conclusion, the Linksys EG24M is an efficient and reliable network switch that combines high-speed connectivity with advanced features like PoE, VLAN support, and enhanced security. Its design and capabilities make it a valuable asset for any business looking to improve its network infrastructure. With Linksys backing its technology, the EG24M is poised to deliver exceptional performance and reliability for diverse networking needs.
Top Page Image Contents