Linksys SRW2024P manual Spanning Tree Tab STP Port Settings, Spanning Tree STP Port Settings

Page 72

24-Port 10/100/1000 Gigabit Switch with Webview and PoE

•Long: Specifies 32-bit based values that range from 1-200,000,000. (This is the default.

•Short: Specifies 16-bit based values that range from 1-65535.

Transmission Limit. The maximum transmission rate for BPDUs is specified by setting the minimum interval between the transmission of consecutive protocol messages. (Range: 1-10; Default: 3) Modify the required attributes for STP.

Click Save Settings to save the changes.

Spanning Tree Tab - STP Port Settings

The Port Information and LAG Information screens display the current status of ports and LAGs in the Spanning Tree.

State. Shows if Spanning Tree has been enabled on this interface.

Status. Displays current state of this port within the Spanning Tree:

•Discarding - Port receives STA configuration messages, but does not forward packets.

•Learning - Port has transmitted configuration messages for an interval set by the Forward Delay parameter without receiving contradictory information. Port address table is cleared, and the port begins learning addresses.

•Forwarding - Port forwards packets, and continues learning addresses.

Forward Transitions. The number of times this port has transitioned from the Learning state to the Forwarding state.

Operational Edge Port. This parameter is initialized to the setting for Administrative Edge Port in STP Port Setting detail, but will be set to false if a BPDU is received indicating that another bridge is attached to this port.

Operational Link Type. The operational point-to-point status of the LAN segment attached to this interface. This parameter is determined by manual configuration or by auto-detection, as described for Administrative Link Type in the STP Port Setting detail.

LAG. Indicates if ports are members of a LAG. To configure STP port settings for LAGs, go to the table entry for the LAG number, which is listed after port g24 at the end of the table.

Click Detail to configure STP Port Settings for an interface.

Chapter 5: Using the Web-based Utility for Configuration

Figure 5-45: Spanning Tree - STP Port Settings

63

Spanning Tree Tab - STP Port Settings

Image 72

Contents Port 10/100/1000 Gigabit Switch with Webview and PoE Copyright and Trademarks Word definitionTable of Contents Port 10/100/1000 Gigabit Switch with Webview and PoE Appendix B Windows Help Appendix C Downloading using Xmodem Startup Menu ProceduresGigabit Ethernet Fiber Optic Cabling List of Figures Front Panel23 Port Status 23 Statistics Port Utilization 52 Admin Forwarding Database Introduction WelcomePort 10/100/1000 Gigabit Switch with Webview and PoE Getting to Know the Switch LEDsOther switches or routers PortsLAN Ports Gigabit Expansion PortsConsole Port Connecting the Switch OverviewMaximum Cabling Distances From Maximum Distance Before You Install the Switch Placement Options Desktop PlacementRack-Mount Placement Uplinking the Switch Web-based Utility for ConfigurationUsing the Console Interface for Configuration Configuring the HyperTerminal ApplicationConnecting to the Switch through a Telnet Session COM1 PropertiesConfiguring the Switch through the Console Interface Switch Main MenuSystem Configuration Menu System Information Management Settings User & Password Settings HTTP/HTTPS File Management Restore System Default Settings Port Status PoE Configuration Help Port 10/100/1000 Gigabit Switch with Webview and PoE Using the Web-based Utility for Configuration Accessing the Web-based UtilitySetup Tab Summary Device InformationSystem Information Setup Tab Network Settings IP ConfigurationPoE Information IdentificationSetup Tab Time Set TimeManual AutomaticPort Management Tab Port Settings Sntp ServersPort Setting Port Settings Port Setting DetailPort Management Tab Link Aggregation Port Management Link Aggregration Port Management Tab Lacp 10 Port Management LacpPort Management Tab PoE Power Settings 11 Port Management PoE Power SettingsVlan Management Tab Port Settings Vlan Management Tab Create VlanSingle Vlan Vlan RangeSwitch Port Mode Vlan Management Tab Ports to VlanVlan Management Tab Vlan to Ports 15 Vlan Management Vlan to PortsStatistics Tab Rmon Statistics 17 Statistics Rmon StatisticsStatistics Tab Rmon History History Control TableStatistics Tab Rmon Alarm 20 Statistics Rmon AlarmPort 10/100/1000 Gigabit Switch with Webview and PoE Event Setting Statistics Tab Rmon EventsStatistics Tab Port Utilization Statistics Tab 802.1x StatisticsACL Tab IP Based ACL 25 ACL IP Based ACLPort 10/100/1000 Gigabit Switch with Webview and PoE ACL Tab MAC Based ACL 26 ACL Mac Based ACLSecurity Tab ACL Binding 27 Security ACL BindingSecurity Tab Authentication Servers 28 Security Athentication ServersSecurity Tab 802.1x Settings 29 Security 802.1x SettingsSecurity 802.1x Settings Port Settings Security Tab Ports Security 30 Security Ports SecuritySecurity Tab Https Settings Security Tab Management ACLSecurity Tab SSH Settings 33 Security SSH SettingsSSH Host-Key Settings 34 Security SSH Host-Key SettingsQoS Tab CoS Settings QoS TabQoS Tab Queue Settings CoS to QueuePort to CoS QoS Tab Dscp Settings QoS Tab Diffserv Settings39 QoS Diffserv Settings Edit Class Element Class Map40 QoS Diffserv Settings Edit Policy Element Policy Map QoS Tab Diffserv Port Binding QoS Tab BandwidthSpanning Tree Tab Global Settings Spanning Tree TabSpanning Tree Tab STP Settings 44 Spanning Tree STP SettingsSpanning Tree Tab STP Port Settings 45 Spanning Tree STP Port SettingsPort 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE Multicast Tab Global Settings 46 Multicast Global SettingsMulticast Tab Static Member Ports Multicast Tab Static Router PortsMulticast Tab Member Ports Query Multicast Tab Router Member Ports QueryAdmin Tab User Authentication 51 Admin User AuthenticationAdmin Tab Forwarding Database Address AgingAdmin Tab Snmp Dynamic Address QueryAdmin Tab Log 54 Admin Log55 Admin Log Flash Logging Admin Tab Port Mirroring 57 Admin Port MirroringAdmin Tab Cable Test Admin Tab PingAdmin Tab Save Configuration Admin Tab Jumbo FrameAdmin Tab Firmware Upgrade Admin Tab Http UpgradeAdmin Tab Reboot Admin Tab Factory DefaultAppendixAAboutGigabitEthernetandFiberOpticCabling Gigabit EthernetFiber Optic Cabling Appendix B Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix C Downloading using Xmodem Startup Menu ProceduresFigure C-3 Browse Appendix D Glossary Port 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE Appendix E Specifications Tftp upgrade Xmodem upgradeCable Diagnostics Port MirroringPort-based and 802.1q based VLANs Management VlanOperating Temperature 32 to 104F 0 to 50C To 158F -20 to 70COperating Humidity 10% to 90% Storage Humidity 10% to 95% Appendix F Warranty Information Limited WarrantyAppendix G Regulatory Information FCC StatementPort 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE Port 10/100/1000 Gigabit Switch with Webview and PoE 100 Appendix H Contact Information