3Com DUA1770-0AAA04 manual Important Safety Information

Page 60

60APPENDIX A: SAFETY INFORMATION

Important Safety Information

WARNING: Installation and removal of the unit must be carried out by qualified personnel only.

WARNING: If installing the Switch in a stack with SuperStack 3 units that are narrower than the Switch, the Switch unit must be installed below the narrower units.

WARNING: The unit must be earthed (grounded).

WARNING: Connect the unit to an earthed power supply to ensure compliance with safety standards.

WARNING: Power Cord Set:

This must be approved for the country where it is used:

U.S.A. and Canada

United Kingdom only

Europe only:

■The cord set must be UL-approved and CSA certified.

■The minimum specification for the flexible cord is: No. 18 AWG

Type SV or SJ 3-conductor

■The cord set must have a rated current capacity of at least 10A.

■The attachment plug must be an earth-grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A, 250V) configuration.

■The supply plug must comply with BS1363 (3-pin 13 amp) and be fitted with a 5A fuse which complies with BS1362.

■The mains cord must be <HAR> or <BASEC> marked and be of type H03VVF3GO.75 (minimum).

■The supply plug must comply with CEE 7/7 (“SCHUKO”).

■The mains cord must be <HAR> or <BASEC> marked and be of type H03VVF3GO.75 (minimum).

Denmark	■	The supply plug must comply with section 107-2-D1,
		standard DK2-1a or DK2-5a.
Switzerland	■	The supply plug must comply with SEV/ASE 1011.

WARNING: The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN60320/IEC320 appliance inlet.

Image 60

Contents SuperStack 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Setting UP for Management PIN-OUTS Page About this Guide Conventions Icon DescriptionConvention Description Related DocumentationDocumentation documentation Please include the following information when commenting SuperStack 3 Switch 4900 Series Getting Started Guide3Com recommends that you copy the Docs/referenceguide Directory as a whole to maintain the structure of the filesIntroducing Introducing the Superstack 3 Switch 4900 Series Hardware Features Switches Switch Front View Detail Switch 4900 front viewSwitch 4924 front view Ports cross-over Power/Self Test LED Color Indicates Port Status LEDsModule Status LEDs Unit LEDsSwitch Rear Switch 4900 rear viewPower Socket Switch 4924 rear viewDefault Settings Supported by your SwitchSwitch units, it is returned to these defaults Installing the Switch Package Contents Choosing a SuitableSite Flow through the side panels of the Switch Rack-mountingDesk, or attach it to a wall Have been fittedRepeat steps 2 and 3 for the other side of the Switch Fitting a bracket for rack-mountingInterconnecting two Switch 4900 units Power-up Powering-upSwitch SequencePower System output RJ-45 connector is now a grounded port That contain alignment pins can cause damage to your SwitchYour Switch OptionsSwitch 4950 Gbic OperationApproved Gbic TransceiversFiber SC connector Type 4 Gbic with internal Eeprom fitted Inserting a Gbic Transceiver into a SwitchSwitch 4950 Gbic Operation Installing the Switch Setting UP for Management Setting Up OverviewManual IP Configuration Automatic IP ConfigurationSetting UP for Management Manually Configuring IP Information Pre-requisitesConnecting the Workstation to the Switch Configuring the Workstation with IP InformationSetting Up the Switch with IP Information Using Command Line Interface via Telnet Example top-level command line interface menu Connecting a workstation to the Switch via the console port 19,200 baud Data bitsSetting Up the Switch with IP Information Configured IP ViewingAutomatically Pre-requisites Viewing IP Information via the Console Port Example top-level command line interface menu Refer to Setting Up Command Line Interface Management on Command Line Network Using TelnetInterface Management CLI Management viaSetting Up Web InterfaceChoosing a Browser Over the Network Http//xxx.xxx.xxx.xxxSetting Up Snmp Default UsersPasswords User Default Name Password Access Level Security Device User Modify operation on the web interfaceProblem Solving For Technical Support information, see Appendix DSolving Problems Solutions belowPower LED does not light On powering-up, the Power/Self Test LED lights yellowProblems Solving HardwareFan failure warning message is received For further information about RMON, refer to StatusError message indicating that the Gbic transceiver is faulty Unit fails, no Snmp fan failure message is receivedSolving Communication Problems IP AddressingHow do you obtain a registered IP Address? Safety Information Important Safety Information This must be approved for the country where it is usedImportant Safety Information 3CGBIC91 Gbic SX 3CGBIC92 Gbic LX ’information de Sécurité Importante SchkoAppendix a Safety Information 3CGBIC91 Gbic SX 3CGBIC92 Gbic LX Wichtige Sicherheitsinformationen Der Netzstecker muß die Norm CEE 7/7 erfüllen SchukoWichtige Sicherheitsinformationen Appendix a Safety Information PC-AT Serial Cable Null Modem Cable 9-pin to RS-232 25-pinPin to 9-pin Connectors Modem CableRJ-45 Pin AssignmentsPin Number 10/100BASE-T 1000BASE-T Appendix B PIN-OUTS Physical Dimensions SafetyPower Consumption Same unless otherwise statedPower Supply Protocols Used for AdministrationHeat Dissipation Standards SupportedServices Online TechnicalUsername anonymous Asia, Pacific Rim From this region, emailEurope, Middle East and Africa From this region, enter the URLAsia, Pacific Rim Europe, Middle East and AfricaCountry Telephone Number Asia, Pacific Rim Country Telephone Number Latin America Index NumbersPasswords Regulatory Notices