Rosewill RU102, RU101 user manual Specification, Operation & Installation, Troubleshooting

Power Protection UPS RU101/102					User Manual
					Turn of the UPS and reduce the amount
			The UPS is	The “Battery Backup &
			making a	Surge Protection”	of equipment connected to these
			continuous sound	outlets are overload.	outlets.
			and the “Overload”
		RU-101/102	indicator is light.		Removed all connected equipments
			The UPS does not	Due to age the battery
Rosewill Uninterruptible Power System (UPS) protects your computer hardware from physical			provide expected	does not hold a full	from the UPS and charge the battery at
			runtime.	charge	least 8 hours.
damage and will provide emergency battery backup power to prevent data loss in the event of					Return for service or you can replace
					the battery by ordering one new battery
power problems.
			Connected	The “Battery Backup &	Refer to the Indicator Table “ UPS is
The main features include
			equipments lose	Surge Protection”	making a continuous sound and the
‹	Advanced equipment & data protection from blackouts, brownouts, sags, AC line noise and		power while	outlets are overload.	Overload indicator is light”
			connected to the	The UPS has	The UPS will turn off when the battery
	surges.
			Power the UPS.	exhausted its available	has been depleted during the failure of
	Full analytical high performance micro-processor control with true RMS synchronous
‹				run time.	utility power. Allow UPS to re-charge
	calculation.				before continuing using of the UPS.
				Connected equipment is Ensure the equipment that you want to
‹	Intelligent battery management for battery status, battery power saving & battery
				connected to the wrong	stay powered during a failure of utility
	replacement control.
				outlet.	power is plugged into the “Battery
‹	DC direct start-up capability, complete diagnostic indication and control.				Backup & Surge Protection” outlets.
				The UPS may be faulty. Please Call your agency for further
‹	Built-in USB communication port for RU102.
					troubleshooting.

‹Phone jack for phone and fax lines for RU102.

Specification

Model	RU-101		RU-102
Capacity	600VA/300W		1000VA/500W
Input Voltage Range	120V +15%/- 20%
Output Voltage Range		120V +/-12%
Frequency		50 / 60 Hz auto sensing
Outlets	6 Outlets (3 Battery Backup & Surge)
Lighting / Surge Protection		480 Joules
Transfer Time to Battery/AC		4 ms (typical)
Battery Type	Sealed and leak proof maintenance free lead-acid battery
Battery Specification	12V/5AH×1		12V/9AH x 1
Phone / Fax/ Network	W/O		RJ11/RJ45
Protection
Short Circuit Protection		Circuit breaker
Communication Port	W/O		USB
Operation Temperature	+32℉ ~ 104℉ (0℃ ~ 40℃)
Operation Relative Humidity	0 to 95% non-condensing
Storage Temperature	+5℉ ~ 113℉ (-15℃~ 45℃)
Net Weight	7.8 lbs		9.12 lbs
Dimensions (WxDxH) inch	6.1×4.3×8.3		7.1x6x9.5

Operation & Installation

Rosewill UPS can protect your equipment from all power problems such as surge, spikes, blackouts, brownouts and line noise. When AC power is present and the ON/OFF switch is turned on, Rosewill UPS continues to charge the battery and provide the power to the equipment directly from the AC line. The battery can provide stable power to complete your work, save your data and safely shut down your system when the utility power has failed.

Rosewill UPS is simple to operate and install. Following are the installation steps to connect he equipment to the UPS.

1.Connect Rosewill UPS to grounded AC power Outlets.

2.Charge the battery at least 8 hours for a full charge before use.

3.Plug your computer and monitor into the “Battery Backup & Surge Protection” outlets. (These outlets will provide emergency battery backup power during power problems as well as surge protection from surge and spike.)

CAUTION: Do NOT plug LASER PRINTERS into any of the “Battery Backup” outlets.

CAUTION: Do NOT plug ACCESSORY SURGE STRIP into any of the “Battery Back & Surge Protection” outlets.

4.Plug your peripheral equipment (printer, scanner, fax, speaker, etc.) into the “Surge Protection” outlets. (These outlets will NOT provide battery backup power during a utility power failure).

5.Switch on the Rosewill offline UPS product while the connected equipment is off,.

6.Turn on your connected equipment when the “AC mode” LED light is illuminated.

Troubleshooting

Symptom	Possible Cause	Action to Take
The UPS will not	UPS is not turn on	Switch on the On/Off switch. If the
turn on.		power is not present, please make sure
		your circuit breaker on the building is not
		accidentally turned off.
	Circuit Breaker has	Reduce the amount of equipment
	tripped.	plugged into the “Battery Backup &
		Surge Protection” outlets of the UPS.
		Next, rest the circuit breaker by pushing
		it back in.

Indicators

600VA/300W

1000VA/500W

1.On/Off Switch

This On/Off switch controls power to your equipment and performs a self-test to detect inverter, line, battery status & LEDs.

NOTE: Turn on the UPS.

Press and hold the switch for more than two seconds and release the switch after the beep. The UPS will start and provide the stable power to your equipments.

NOTE: Turn off the UPS.

Press and hold the switch for more than two seconds and release the switch. The UPS will shut down completely.

NOTE: Perform Self-test.

The UPS will perform self-test for about 10 seconds when the UPS is turned on.

2.Line / Battery LED (Green LED)

Indicates the UPS is providing AC power to your equipment. When the LED is blinking the UPS is providing power from the battery.

3.Warning LED (Red)