Rosewill RNX-N150RT user manual TCP/IP Configuration, ¾ Configure the IP address manually

Page 17

Wireless Router RNX-N150RT		User Manual

Chapter 3. Quick Installation Guide

This chapter will show you how to configure the basic functions of your RNX-N150RT 150Mbps Wireless Lite N Router using Quick Setup Wizard within minutes.

3.1 TCP/IP Configuration

The default IP address of the RNX-N150RT 150Mbps Wireless Lite N Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.

Connect the local PC to the LAN ports of the Router. And then you can configure the IP address for your PC in the following two ways.

¾Configure the IP address manually

1)Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC".

2)Configure the network parameters. The default IP address is 192.168.1.xxx ("xxx" is any number from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The Router's default IP address)

¾Obtain an IP address automatically

1)Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC”.

2)Then the built-in DHCP server will assign IP address for the PC.

Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the Router. The following example is in Windows 2000 OS.

Open a command prompt, and type ping 192.168.1.1, and then press Enter.

¾If the result displayed is similar to the Figure 3-1,it means the connection between your PC and the Router has been established well.

- 10 -

Image 17

Contents Wireless Router RNX-N150RT Copyright & Trademarks Country Restriction Reason/remark FCC RF Radiation Exposure StatementRadiation Exposure Statement Industry Canada statementWireless Router RNX-N150RT Table of Contents RNX-N150RT 102 Package Contents Flexible Access Control Overview of the Wireless RouterIncredible Speed Multiple Security ProtectionsSimple Installation Main FeaturesFront Panel Panel LayoutWlan Name Status IndicationRear Panel ¾ RESET：System Requirements Installation Environment RequirementsConnecting the Router Wireless Router RNX-N150RT ¾ Obtain an IP address automatically TCP/IP Configuration¾ Configure the IP address manually Failure result of Ping command Please check the connection following these steps Quick Installation GuideQuick Installation Guide Click on Quick Setup Wireless Router RNX-N150RT Click Finish and you are ready Login Windows Quick Installation Guide Detail and ExplanationWireless Router RNX-N150RT Quick Setup PPPoE Wireless Router RNX-N150RT 11 Quick Setup Finish PSK Password You can enter Ascii or Hexadecimal charactersFunctions Configuring the RouterWireless Router RNX-N150RT Status Details Quick SetupWPS Setup Wireless Router RNX-N150RT Method One By Push Button Configuration PBCMethod Two Add a New Device Method ThreeWireless Router RNX-N150RT Next By PINWireless Router RNX-N150RT 1 LAN Network2 WAN Wireless Router RNX-N150RT Wireless Router RNX-N150RT Wireless Router RNX-N150RT Wireless Router RNX-N150RT NSW / ACT nsw.bigpond.net.au Wireless Router RNX-N150RT Wireless Router RNX-N150RT Wireless Router RNX-N150RT Wireless Router RNX-N150RT MAC Clone Wireless Settings WirelessWireless Router RNX-N150RT Wireless Router RNX-N150RT 18 Wireless Security Wireless Security¾ WPA /WPA2 It’s based on Radius Server Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering To modify or delete an existing entry 23 Add or Modify Wireless MAC Address Filtering entry24 Wireless Advanced Wireless AdvancedWireless Statistics 26 The Dhcp menu Dhcp SetupDhcp Settings Address Reservation Dhcp Clients List30 Add or Modify an Address Reservation Entry To Reserve an IP addressVirtual Servers Forwarding33 Add or Modify a Virtual Server Entry To setup a virtual server entryPort Triggering To add a new rule, follow the steps below 3 DMZ 35 Add or Modify a Port Triggering EntryUPnP To assign a computer or server to be a DMZ serverBasic Security SecurityWireless Router RNX-N150RT Advanced Security Local Management Remote Management 41 Local ManagementAccess Control To add a new rule, please follow the steps below RuleWireless Router RNX-N150RT Host 46 Host Settings47 Add or Modify a Host Entry To add a new entry, please follow the steps belowTarget 50 Add or Modify an Access Target Entry Schedule To add a new schedule, follow the steps below 11Static Routing To add static routing entries, follow the steps below 54 Static Routing12Bandwidth Control Control SettingsRules List 59 Bandwidth Control Rule Settings Click the Save buttonBinding Settings 13IP& MAC Bing SettingTo find an existing entry, follow the steps below To add IP & MAC Binding entries, follow the steps belowARP List Dyndns.org Ddns To set up for DDNS, follow these instructions14Dynamic DNS Wireless Router RNX-N150RT 15System Tools Time SettingsTo configure the system automatically To configure the system manuallyDiagnostic Firmware Upgrade 70 Diagnostic ResultsFactory Defaults Reboot Backup & RestoreSystem log PasswordWireless Router RNX-N150RT Statistics Wireless Router RNX-N150RT MAC Address Packets Statistics Table IP AddressTotal Bytes Packets Statistic interval seconds BytesAppendix a FAQ Want to use NetMeeting, what do I need to do? Figure A-3 MAC CloneFigure A-4 Virtual Servers Want to build a WEB Server on the LAN, what should I do? Figure A-7 Basic SecurityBrowser Wireless stations cannot connect to the RouterConfigure TCP/IP component Appendix B Configuring the PCShown in the Figure below Figure B-3 ¾ Setting IP address manuallyNow Figure B-4Wireless Frequency Band Safety & EmissionsGeneral Standards ProtocolsSensitivity @PER TemperatureAntenna Gain Environmental and PhysicalAppendix D Glossary 109