Rosewill RNX-N150RT user manual Dhcp Settings

Page 61

Wireless Router RNX-N150RT		User Manual

There are three submenus under the DHCP menu (shown in Figure 4-26),DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function.

4.7.1DHCP Settings

Choose menu “DHCP → DHCP Settings”, you can configure the DHCP Server on the page as shown in Figure 4-27.The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN.

Figure 4-27 DHCP Settings

¾DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.

¾Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.1.100 is the default start address.

¾End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.1.199 is the default end address.

¾Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.

¾Default Gateway - (Optional.) It is suggested to input the IP address of the LAN port of the Router. The default value is 192.168.1.1.

- 54 -

Image 61

Contents Wireless Router RNX-N150RT Copyright & Trademarks Country Restriction Reason/remark FCC RF Radiation Exposure StatementRadiation Exposure Statement Industry Canada statementWireless Router RNX-N150RT Table of Contents RNX-N150RT 102 Package Contents Flexible Access Control Overview of the Wireless RouterIncredible Speed Multiple Security ProtectionsSimple Installation Main FeaturesFront Panel Panel LayoutWlan Name Status IndicationRear Panel ¾ RESET：Connecting the Router Installation Environment RequirementsSystem Requirements Wireless Router RNX-N150RT ¾ Configure the IP address manually TCP/IP Configuration¾ Obtain an IP address automatically Failure result of Ping command Quick Installation Guide Quick Installation GuidePlease check the connection following these steps Click on Quick Setup Wireless Router RNX-N150RT Click Finish and you are ready Login Windows Quick Installation Guide Detail and ExplanationWireless Router RNX-N150RT Quick Setup PPPoE Wireless Router RNX-N150RT 11 Quick Setup Finish PSK Password You can enter Ascii or Hexadecimal charactersFunctions Configuring the RouterWireless Router RNX-N150RT WPS Setup Quick SetupStatus Details Wireless Router RNX-N150RT Method One By Push Button Configuration PBCMethod Two Add a New Device Method ThreeWireless Router RNX-N150RT Next By PINWireless Router RNX-N150RT 1 LAN Network2 WAN Wireless Router RNX-N150RT Wireless Router RNX-N150RT Wireless Router RNX-N150RT Wireless Router RNX-N150RT NSW / ACT nsw.bigpond.net.au Wireless Router RNX-N150RT Wireless Router RNX-N150RT Wireless Router RNX-N150RT Wireless Router RNX-N150RT MAC Clone Wireless Settings WirelessWireless Router RNX-N150RT Wireless Router RNX-N150RT 18 Wireless Security Wireless Security¾ WPA /WPA2 It’s based on Radius Server Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering To modify or delete an existing entry 23 Add or Modify Wireless MAC Address Filtering entry24 Wireless Advanced Wireless AdvancedWireless Statistics 26 The Dhcp menu Dhcp SetupDhcp Settings Address Reservation Dhcp Clients List30 Add or Modify an Address Reservation Entry To Reserve an IP addressVirtual Servers Forwarding33 Add or Modify a Virtual Server Entry To setup a virtual server entryPort Triggering To add a new rule, follow the steps below 3 DMZ 35 Add or Modify a Port Triggering EntryUPnP To assign a computer or server to be a DMZ serverBasic Security SecurityWireless Router RNX-N150RT Advanced Security Local Management Remote Management 41 Local ManagementAccess Control To add a new rule, please follow the steps below RuleWireless Router RNX-N150RT Host 46 Host Settings47 Add or Modify a Host Entry To add a new entry, please follow the steps belowTarget 50 Add or Modify an Access Target Entry Schedule To add a new schedule, follow the steps below 11Static Routing To add static routing entries, follow the steps below 54 Static Routing12Bandwidth Control Control SettingsRules List 59 Bandwidth Control Rule Settings Click the Save buttonBinding Settings 13IP& MAC Bing SettingTo find an existing entry, follow the steps below To add IP & MAC Binding entries, follow the steps belowARP List 14Dynamic DNS To set up for DDNS, follow these instructionsDyndns.org Ddns Wireless Router RNX-N150RT 15System Tools Time SettingsTo configure the system automatically To configure the system manuallyDiagnostic Firmware Upgrade 70 Diagnostic ResultsFactory Defaults Reboot Backup & RestoreSystem log PasswordWireless Router RNX-N150RT Statistics Wireless Router RNX-N150RT MAC Address Packets Statistics Table IP AddressTotal Bytes Packets Statistic interval seconds BytesAppendix a FAQ Want to use NetMeeting, what do I need to do? Figure A-3 MAC CloneFigure A-4 Virtual Servers Want to build a WEB Server on the LAN, what should I do? Figure A-7 Basic SecurityBrowser Wireless stations cannot connect to the RouterConfigure TCP/IP component Appendix B Configuring the PCShown in the Figure below Figure B-3 ¾ Setting IP address manuallyNow Figure B-4Wireless Frequency Band Safety & EmissionsGeneral Standards ProtocolsSensitivity @PER TemperatureAntenna Gain Environmental and PhysicalAppendix D Glossary 109