Rosewill RNX-N180PCE Product Specification, Standard, Interface, Receiver Sensitivity, Channel

Page 7

1.5Product Specification

Wireless N Adapter RNX-N180PCe		User Manual

1.5Product Specification

Standard

IEEE 802.11n draft 2.0, IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u

Interface

1Wireless 1T2R PCI-E Card（PCI ExpressTM Base Specification Revision 1.1） 2 2x 2dB reverse SMA detachable antennas (Standard 1.8dB)

Receiver Sensitivity

300Mbps Typical -68 dBm

54Mbps Typical -73 dBm

11Mbps Typical -84 dBm

Channel

USA 11, Europe 13, Japan 14

Transmit Power

16dBm typically @ 802.11b 14dBm typically @ 802.11g 13dBm typically @ 802.11n

Network Data Rate 802.11b: 1,2,5.5 and 11Mbps

802.11g: 6,9,12,18,24,36,48 and 54Mbps

802.11n: up to 300Mbps

Temperature

Operating: 0°C ~ 40°C (32°~104°F)

Storage: -10°C ~ 70°C (14°~158°F)

Humidity

Operating: 10% ~ 90% RH, non-condensing

Storage: 5%~90% RH, non-condensing

Emission

FCC, CE, VCCI Class B

7

Image 7

Contents User Manual Wireless N Adapter RNX-N180PCeRestriction Wireless N Adapter RNX-N180PCe2400.0-2483.5 MHz CountryWireless N Adapter RNX-N180PCe Table of Content Easy Installation, enhanced Wireless Security Package ContentChapter 1 Overview 1.1 Overview of the ProductLED Indications 1.2 Features1.3 System Requirement 1.4 LED StatusInterface 1.5 Product SpecificationTransmit Power Standard2.1 Hardware Installation Chapter 2 Installation Guide2.2 Software Installation for Windows OS 5. Click Next 6. Click Install to start installing 8. Now your PC or notebook will restart automatically 7. Follow the InstallShield Wizard steps, and click Finish when doneUser Manual Chapter 3 Wireless Connection Guide 3.1 Connecting with Microsoft Zero Configuration tool Win XP3.2 Connecting with Window 3.3 Connecting with Wireless LAN Utility 3.3.2 Step 2 Select and Add to Profile 3.3.1 Step 1 Search Available NetworkAfter click “Add to Profile”, you will see the next window “Wireless Network Properties” popup with your current wireless signal’s setting. RNX-N180PCe will detect the current setting of your SSID. So after the “Wireless Network Properties” popup, all you need to do is to enter the password of your SSID and click OK to continute 4.1 General Chapter 4 Utility Configuration - Win XP’s Station Mode Create a new Infrastructure mode profile 4.1.1 ProfileNetwork Address Others Create a new ad-hoc mode profile 4.1.1.2 Remove 4.1.1.3 Editcreated a profile Modify the profile information according to your demand 4.1.1.4 DuplicateSelect a profile which you want to copy and then click Duplicate Import the new profile name in the popup window blank 4.1.1.5 Set defaultDouble-click the network to which you wish to connect 4.2 Available Network4.3 Status 4.4 Statistics 4.5.1 Method 1 PIN Input Config PIN 4.5 Wi-Fi Protect Setup2. Click Pin Input ConfigPIN WPS config page1. Click Push Button ConfigPBC on Wi-Fi Protect Setup page 4.5.2 Method 2 Push Button2. Click Start PBC on the AP-Router WPS config page Remark 5.1 General Chapter 5 Configuration - Win XP’s Access Point Mode Network name SSID 5.2 Advanced Network authentication  Profile name DTIM period 5.3 Statistics Set defaults  Beacon IntervalIt display receive and transmit information 5.4 ICSUser Manual Wireless N Adapter RNX-N180PCePage multiple clients associated to it Glossary Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the receiver can recover the original data without the need of retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected ignored by most narrowband receivers. However, to an intended receiver i.e. another wireless LAN endpoint, the DSSS signal is recognized as the only valid signal, and interference is inherently rejected ignored  WEP - Wired Equivalent Privacy - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64-bit encryption. Keys are defined by entering in a string in HEX hexadecimal - using characters 0-9, A-F or ASCII American Standard Code for Information Interchange - alphanumeric characters format. ASCII format is provided so you can enter a string that is easier to remember. The ASCII string is converted to HEX for use over the network. Four keys can be defined so that you can change keys easily