Rosewill RNX-N180PCE user manual Software Installation for Windows OS

Page 9

2.2Software Installation for Windows OS

Wireless N Adapter RNX-N180PCe		User Manual

2.2Software Installation for Windows OS

The following driver installation guide uses Windows XP as the presumed operation system.

1.The system finds the newly installed device automatically. Click Cancel to close this window.

2.Insert the Driver and Utility CD-ROM into the CD-ROM driver.

3.The Wizard should run automatically, and Error! Reference source not found. should appear. If not, click the Start button and choose Run. In the field that appears, enter D:\autorun.exe (if ‘’D’’ is the letter of your CD-ROM drive).

4.Click Install Driver Installation on the Wireless Client Configuration Utility dialogue

9

Image 9

Contents User Manual Wireless N Adapter RNX-N180PCe2400.0-2483.5 MHz Wireless N Adapter RNX-N180PCeCountry RestrictionWireless N Adapter RNX-N180PCe Table of Content Chapter 1 Overview Package Content1.1 Overview of the Product Easy Installation, enhanced Wireless Security1.3 System Requirement 1.2 Features1.4 LED Status LED IndicationsTransmit Power 1.5 Product SpecificationStandard Interface2.1 Hardware Installation Chapter 2 Installation Guide2.2 Software Installation for Windows OS 5. Click Next 6. Click Install to start installing 8. Now your PC or notebook will restart automatically 7. Follow the InstallShield Wizard steps, and click Finish when doneUser Manual Chapter 3 Wireless Connection Guide 3.1 Connecting with Microsoft Zero Configuration tool Win XP3.2 Connecting with Window 3.3 Connecting with Wireless LAN Utility 3.3.2 Step 2 Select and Add to Profile 3.3.1 Step 1 Search Available NetworkAfter click “Add to Profile”, you will see the next window “Wireless Network Properties” popup with your current wireless signal’s setting. RNX-N180PCe will detect the current setting of your SSID. So after the “Wireless Network Properties” popup, all you need to do is to enter the password of your SSID and click OK to continute 4.1 General Chapter 4 Utility Configuration - Win XP’s Station ModeNetwork Address 4.1.1 ProfileOthers  Create a new Infrastructure mode profile Create a new ad-hoc mode profile 4.1.1.3 Edit 4.1.1.2 Removecreated a profile 4.1.1.4 Duplicate Modify the profile information according to your demandSelect a profile which you want to copy and then click Duplicate Import the new profile name in the popup window blank 4.1.1.5 Set defaultDouble-click the network to which you wish to connect 4.2 Available Network4.3 Status 4.4 Statistics 4.5.1 Method 1 PIN Input Config PIN 4.5 Wi-Fi Protect Setup2. Click Pin Input ConfigPIN WPS config page4.5.2 Method 2 Push Button 1. Click Push Button ConfigPBC on Wi-Fi Protect Setup page2. Click Start PBC on the AP-Router WPS config page Remark 5.1 General Chapter 5 Configuration - Win XP’s Access Point Mode Network authentication 5.2 Advanced Profile name  Network name SSID Set defaults 5.3 Statistics Beacon Interval  DTIM periodIt display receive and transmit information 5.4 ICSUser Manual Wireless N Adapter RNX-N180PCePage multiple clients associated to it Glossary Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the receiver can recover the original data without the need of retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected ignored by most narrowband receivers. However, to an intended receiver i.e. another wireless LAN endpoint, the DSSS signal is recognized as the only valid signal, and interference is inherently rejected ignored  WEP - Wired Equivalent Privacy - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64-bit encryption. Keys are defined by entering in a string in HEX hexadecimal - using characters 0-9, A-F or ASCII American Standard Code for Information Interchange - alphanumeric characters format. ASCII format is provided so you can enter a string that is easier to remember. The ASCII string is converted to HEX for use over the network. Four keys can be defined so that you can change keys easily