RocketFish RF-PHD25 warranty Package contents, System requirements, Contenu du carton

PATA 2.5 Hard Drive Enclosure

Boîtier pour disque dur PATA de 2,5 po (6,35 cm)

Caja para disco duro PATA de 2.5"

Package contents

•	RF-PHD25 enclosure	•	Carrying case
•	High-speed USB 2.0 Y-cable	•	Screws (4)
• CD that contains Roxio BackOnTrack		•	Screwdriver
	backup software and User Guide	•	Quick Setup Guide

System requirements

One USB port

Windows® 7, Windows Vista®, Windows® XP, or Mac OS 10.2.0 or higher.

Installing your hard drive in the enclosure

1Remove the two screws from the back panel, then pull the tray out from the enclosure.

2Place a formatted hard drive into the tray, connect the data connector to the corresponding connector on the enclosure board, then turn the tray over and secure the drive to the metal plate with the two screws (provided).

3Slide the assembled tray back into the enclosure, then secure it with the two screws you previously removed.

One connector is for data and bus power. The other connector is for additional power, if required. When you connect the USB 2.0 Y cable to the computer, use both A male-type connectors to make sure the enclosure has sufficient power. The operating system automatically detects and sets up the new drive.

2If the drive is not formatted, please take the steps below to format the drive.

For Macintosh users:

1 Double-click on Macintosh HD.

2 Click the Applications folder.

3 Click the Utilities folder.

4 Double-click Disk Utility.

5 On the left side of the window, there are the drives connecting to the computer. Select the drive you want to format and then click the Erase tab.

6 Verify Volume Format is set to MS-DOS file system, then click Erase.

For Windows users:

1 Right-click My Computer and select Manage.

2 Click Disk Management on the left pane.

3 Right-click on the drive/device you want to format then select Format.

4 Occasionally, a warning may come out concerning active partition, click Yes.

5 Click OK to format.

Installing the backup software

Notes:

•The Roxio BackOnTrack software only runs on Windows Vista, Windows XP, or Windows 7. computers using USB.

•Connect the hard drive enclosure to your computer before installing the software.

•Before installing the backup software, make sure that your Windows operating system has been updated to the latest service pack.

1	Save all files and close all programs.
2	Insert the included CD into the computer. The introductory screen
	appears automatically. If the screen does not appear, double-click
	the autorun.exe file on the CD.
3	Click Install Roxio® BackOnTrack™ 3 LE. The Welcome screen opens.
4	Click Next to begin the installation.
5	Follow the instructions in the setup wizard, then click Next to
	continue.
6	Click Finish to finalize installation.

Contenu du carton

•	Boîtier RF-PHD25	•	Étui de transport
• Câble en Y USB 2.0 à haut débit		•	Vis (4)
•	CD avec l’application de sauvegarde Roxio	•	Tournevis
	BackOnTrack et le Guide de l’utilisateur	•	Guide d’installation rapide

Configuration système requise

Un port USB

WindowsMD 7,WindowsVistaMD,WindowsMD XP ou Mac OS 10.2.0 ou supérieur.

Installation du disque dur dans le boîtier

1Retirer les deux vis du panneau arrière, puis extraire le plateau du boîtier.

2Placer un disque dur formaté sur le plateau, connecter le connecteur de données au connecteur correspondant de la carte du boîtier, puis retourner le boîtier et fixer le disque dur à la plaque métallique à l’aide des deux vis (fournies).

3Replacer le plateau assemblé dans le boîtier, puis le fixer avec les deux vis retirées précédemment.

Connexion du boîtier à l’ordinateur

Connecting the enclosure to a computer

1 Plug a USB 2.0 cable into the enclosure, then plug the cable into a USB port on the computer. The operating system automatically recognizes the new drive.

Note: The enclosure comes with a USB 2.0 Y cable, which has two standard

USB A male-type connectors.

RF-PHD25	QUICK SETUP GUIDE • GUIDE D’INSTALLATION RAPIDE •
	GUÍA DE INSTALACIÓN RÁPIDA

7 See the User Guide located on the CD for information on using the

software.

Disconnecting the enclosure from your computer

For Windows users:

1Right-click the Hotplug icon (located near the clock on the taskbar).

2Select the device you want to unplug, then click STOP.

3When Windows notifies you that it is safe to do so, unplug the enclosure from your computer.

For Macintosh users:

1Drag the USB icon into the TRASH.

2Unplug the enclosure.

One-year limited warranty

Visit www.rocketfishproducts.com for details

© 2009 Best Buy Enterprise Services, Inc. Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN USA 55423-3645

1Brancher un câble USB 2.0 sur le boîtier, puis brancher le câble sur un port USB de l’ordinateur. Le système d’exploitation reconnaît automatiquement le nouveau disque.

Remarque : le boîtier est fourni avec un câble USB en Y, qui a deux connecteurs standard USB A de type mâle.