Metrik Mobile Electronics MCD-797 Trouble Shooting, Fader Control, Dspoff/Pop/Rock/Classic/Flat

5)FADER CONTROL

A.Press the SEL button to select the fader mode until FAD appears on the display.

B.Rotate the VOL knob to increase or decrease the sound level of front or rear speaker.

(2)When pressed longer 2 seconds, it is activated as cyclical mode of following functions for users selection.

-> BEEP (2nd/ALL/OFF) ->SEEK1/ 2 -> DSP(OFF/POP/ROCK/CLASSIC/FLAT) -> VOL LAST/VOL ADJ -> ESP 40 seconds/10 seconds mode.

After selecting the desired mode, rotate the VOL knob to select one setup item of the desired mode.

BEEP 2ND, BEEP ALL, BEEP OFF MODE

The situation of beep sound is selected. The 3 mode is selected as also rotating the VOL knob.

-Beep 2nd mode:

The beep is only hears when a function key is pressed for more than 1 second.

-Beep all mode:

The beep is generated when every key is pressed.

-Beep off mode:

The beep sound is disabled when a key is pressed.

SEEK 1/SEEK 2 mode:( Only available during radio operation)

SEEK 1: Press and hold the >> or << button to seek up or down for a station with a strong signal. The seek stops when a station is reached .

SEEK 2: Press and hold the >> or << button to seek up or down for a station with a strong signal. The seek does not stop until the >> or << button is released.

DSP(OFF/POP/ROCK/CLASSIC/FLAT):

The unit is equipped with 4 preset equalization modes. After entering this mode by pressing the SEL button, rotate the VOL knob in the clockwise direction to choose one of 4 preset EQs in the above order. When using preset EQ modes you will not have access to Bass and Treble settings.

VOL LAST/VOL ADJ:

VOL LAST: The radio switches on at the actual volume it had when it was last switched off.

VOL ADJ: Rotating the VOL knob you can pre-select a constant switch-on volume after entering into this mode.

ESP 40 /10 seconds:

Briefly press the SEL button to access the ESP function (anti-shock system which improves playback if there are shocks or vibrations); you can choose between two lengths of time for ESP, either 40 seconds (ESP 40) or 10 seconds (ESP 10) by rotating the VOL knob.

2.COVER of MMC/SD and USB SOCKET

When needing to do MMC/SD or USB operation, uncover the cover, then insert the MMC/SD card or USB bar into MMC/SD compartment or USB socket.

When no using the MMC/SD or USB device, please cover it with the cover after pulling them out of the MMC/SD slott or the USB socket.

3.LCD (LIQUID CRYSTAL DISPLAY)

4.TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONS

1)In RADIO mode, press >> or << button shortly and repeatedly to manually tune up or down for the desired radio station with step by step. Press >> or << button hold for more than 0.5 seconds to auto-matically tune up or down for the radio station of strong signal.

2)In MMC/SD, USB or DISC mode, press >> button to play next track. Press << button once to play the current track from the beginning of the current track, press << button twice continuously to play the last track. Press >> or << button hold to skip forward or backward.

TROUBLE SHOOTING

Before using the check list please make all the connections first.

If you still have questions after going through the checklist, please consult your local customer service representative.

Common Symptoms	Cause	Solution
	The car ignition is switched off.	If the power supply is properly connected to
There is no power.		the car accessory, switch the ignition key to
		" ON " or " ACC " .
	The fuse has blown.	Replace another fuse according to the wiring
		diagram.
The CDs can not	A disc is inside the player.	Remove the disc in the player then put a new
be loaded.		upward
The CDs are loaded	The transport screws have not been	Remove the transport screws before using.
only halfway into	removed.
the CD tray.
	The disc is inserted upside-down.	Insert the compact disc with the label facing
The device does		upward
	The surface of CD is extremely dirty	Clean the CD or try another CD, if this works
not work correctly
(EJECT, LOAD,	or it is damaged.	correctly, the first CD is properly damaged.
PLAY)
	Temperature inside the car is too	Cool off until the ambient temperature returns
	high.	to normal
There is no sound.	The volume control is set too low.	Turn up the volume properly.
	The device has not been correctly	Check the power and earth connection
	connected.	according to the wiring diagram.
	1.The built-in microcomputer is not	1. Switch the device off and on again. Or press
The operation keys	operating properly due to noise	the RESET button to resume the program.
do not work	2.The front panel is not properly	2. Reinstall the front panel
	installed.
	The installation angle is more than	Adjust the installation angle to less than 30
	30 degrees	degrees
The sound of the	The surface of the road is uneven.	Wait until the road becomes smoother before
CD player skips		playing the CD.
	The surface of CD is extremely dirty	Clean the CD or try another CD, if this works
	or it is damaged.	correctly, the first CD is properly damaged.
No radio reception.	The antenna cable is not connected.	Insert the antenna cable firmly into the
		antenna socket of the device.
In automatic search	The transmission signals are too	Tune in to a radio station manually.
mode the radio does	weak.
not stop at a trans-
mitting station.

Page 3 Page 12