Symbol Technologies LS 2106 manual Convert I 2 of 5 to EAN-13

Page 57

Parameter Menus

Convert I 2 of 5 to EAN-13

This parameter converts a 14 character I 2 of 5 code into EAN-13, and transmits to the host as EAN-13. In order to accomplish this, the I 2 of 5 code must be enabled, one length must be set to 14, and the code must have a leading zero and a valid EAN-13 check digit.

CONVERT I 2 of 5 to EAN-13

(ENABLE)

DO NOT CONVERT I 2 of 5 to EAN-13

(DISABLE)

4-37

Image 57

Contents About This Manual Table of Contents Glossary Copyright Contents Parameter Menus Ascii Character Set Service Information Notational ConventionsRelated Publications Introduction Chapter Setting Up the LSUnpacking AudienceSwitching Cables Setting Up the LSConnecting to a Host Scanning with the LS Chapter Scanning with the LSAiming the Scanner What Does The Beep Mean? LS 2106 Decode Zone Troubleshooting MaintenanceDescription Part Number AccessoriesTechnical Speciﬁcations 167 mm 70 mm 85 mm Pin Signal Name Function LS 2106 Signal DescriptionsPin Connector Beeper Indications Chapter Parameter Menus Parameter Default Number Default ParametersCode Interleaved 2 Parameter Default Number CodeDiscrete 2 CodabarParameter Number MSI PlesseyData Options Parameter Default Number Keyboard Wedge Set Default Parameter Beeper Volume Laser On Time Power Mode Do Not Beep After Good Decode Beep After Good DecodeDo Not Transmit No Read Message Transmit No Read MessageDecode Redundancy Autodiscriminate Response Time Enable/Disable UPC-E/UPC-A Enable/Disable EAN-8/EAN-13 Enable/Disable Bookland EAN Decode UPC/EAN Supplementals Transmit UPC-A/UPC-E Check Digit UPC-A Preamble UPC-E Preamble Convert UPC-E to UPC-A EAN Zero Extend EAN Zero Extend Code Type Enable/Disable Code Enable/Disable UCC/EAN-128 Enable/Disable Code Code 39 Check Digit Veriﬁcation Do Not Transmit Code 39 Check Digit Transmit Code 39 Check DigitEnable/Disable Code 39 Full Ascii Code 39 Buffering Scan & Store Buffer Data Transmit Buffer Enable/Disable Code Enable/Disable Interleaved 2 Set Lengths for Interleaved 2 Convert I 2 of 5 to EAN-13 Enable/Disable Discrete 2 Set Lengths for Discrete 2 Enable/Disable Codabar Clsi Editing Notis Editing Enable/Disable MSI Plessey MSI Plessey Check Digits Do Not Transmit MSI Plessey Check Digit Transmit MSI Plessey Check DigitMSI Plessey Check Digit Algorithm Transmit Code ID Character Symbol Code ID Character AIM Code ID Character None Preﬁx/Sufﬁx Values Scan Data Transmission Format Scan Data Transmission Format cont’d Host Interfaces National Keyboard Types Spanish Italian Swedish British Fast Transmit Intercharacter Delay Numeric Bar Codes Numeric Bar Codes cont’d Cancel IBM PC/XT Keyboard Keyboard MapsIBM PS2 Keyboard NCR 7052 58-Key Keyboard Ascii Value Full Ascii Keystroke Code Encode Char Appendix a Ascii Character SetCtrl N Ascii Character Set Table A-1. Ascii Character Set Table A-1. Ascii Character Set ALT Keys Keystroke Misc. Key Keystroke PF Keys Keystrokes Keys Keystroke Numeric Keystroke Keypad Extended Keystroke Keypad Table A-1. Ascii Character Set Autodiscrimination ApertureBar Bar Code DensityCdrh Class ByteCharacter Character SetContinuous Code Code LengthDead Zone DecodeIEC 825 Class LED IndicatorIntercharacter Gap Interleaved Bar CodeProgramming Mode Print Contrast SignalResolution Scanning ModeSymbol Length SymbolSymbology Substrate