Symbol Technologies LS 2106 manual Connecting to a Host

Page 9

LS 2106 Product Reference Guide

Connecting to a Host

Plug the connector at the end of the LS 2106 cable into the appropriate port on the Symbol interface controller or portable terminal. Refer to the controller user documentation for full details.

LS 2106	LS 2106	Host
LS 2106	LS 2106	Host

		Controller
PDT
Connecting to a PDT		Host Connection through a Controller
Connecting to a PDT
Host	LS 2106	Host		LS 2106
Synapse		Synapse
Smart		Synapse
Smart		Smart
Cable	Synapse	Smart
Cable	Synapse	Cable
	Adapter
	Cable			Synapse
				Adapter
	Power	Power Supply		Cable
	Supply	(As Req’d_
OCIA via Synapse	(As Required)
OCIA via Synapse		RS-232 via Synapse Adapter Cable
Host	LS 2106	IBM 4683/84/93/94 C		LS 2106
		Cash Register
		Synapse
		Smart
		Cable	Synapse
			Adapter
Power Supply			Cable
Power Supply
(As Required)		IBM via Synapse Adapter Cable
		IBM via Synapse Adapter Cable
Direct RS-232 Connection
	LS 2106	Host		LS 2106
Host		Synapse
		Synapse
		Smart
			Cable
			Power Supply
Keyboard Wedge			(As Required)
Keyboard Wedge		Keyboard Wedge via Synapse

Figure 1-3. Connecting to a Host

1-4

Image 9

Contents About This Manual Table of Contents Glossary Copyright Contents Parameter Menus Ascii Character Set Service Information Notational ConventionsRelated Publications Introduction Chapter Setting Up the LSUnpacking AudienceSwitching Cables Setting Up the LSConnecting to a Host Scanning with the LS Chapter Scanning with the LSAiming the Scanner What Does The Beep Mean? LS 2106 Decode Zone Troubleshooting MaintenanceDescription Part Number AccessoriesTechnical Speciﬁcations 167 mm 70 mm 85 mm Pin Signal Name Function LS 2106 Signal DescriptionsPin Connector Beeper Indications Chapter Parameter Menus Parameter Default Number Default ParametersCode Interleaved 2 Parameter Default Number CodeDiscrete 2 CodabarParameter Number MSI PlesseyData Options Parameter Default Number Keyboard Wedge Set Default Parameter Beeper Volume Laser On Time Power Mode Do Not Beep After Good Decode Beep After Good DecodeDo Not Transmit No Read Message Transmit No Read MessageDecode Redundancy Autodiscriminate Response Time Enable/Disable UPC-E/UPC-A Enable/Disable EAN-8/EAN-13 Enable/Disable Bookland EAN Decode UPC/EAN Supplementals Transmit UPC-A/UPC-E Check Digit UPC-A Preamble UPC-E Preamble Convert UPC-E to UPC-A EAN Zero Extend EAN Zero Extend Code Type Enable/Disable Code Enable/Disable UCC/EAN-128 Enable/Disable Code Code 39 Check Digit Veriﬁcation Do Not Transmit Code 39 Check Digit Transmit Code 39 Check DigitEnable/Disable Code 39 Full Ascii Code 39 Buffering Scan & Store Buffer Data Transmit Buffer Enable/Disable Code Enable/Disable Interleaved 2 Set Lengths for Interleaved 2 Convert I 2 of 5 to EAN-13 Enable/Disable Discrete 2 Set Lengths for Discrete 2 Enable/Disable Codabar Clsi Editing Notis Editing Enable/Disable MSI Plessey MSI Plessey Check Digits Do Not Transmit MSI Plessey Check Digit Transmit MSI Plessey Check DigitMSI Plessey Check Digit Algorithm Transmit Code ID Character Symbol Code ID Character AIM Code ID Character None Preﬁx/Sufﬁx Values Scan Data Transmission Format Scan Data Transmission Format cont’d Host Interfaces National Keyboard Types Spanish Italian Swedish British Fast Transmit Intercharacter Delay Numeric Bar Codes Numeric Bar Codes cont’d Cancel IBM PC/XT Keyboard Keyboard MapsIBM PS2 Keyboard NCR 7052 58-Key Keyboard Ascii Value Full Ascii Keystroke Code Encode Char Appendix a Ascii Character SetCtrl N Ascii Character Set Table A-1. Ascii Character Set Table A-1. Ascii Character Set ALT Keys Keystroke Misc. Key Keystroke PF Keys Keystrokes Keys Keystroke Numeric Keystroke Keypad Extended Keystroke Keypad Table A-1. Ascii Character Set Autodiscrimination ApertureBar Bar Code DensityCdrh Class ByteCharacter Character SetContinuous Code Code LengthDead Zone DecodeIEC 825 Class LED IndicatorIntercharacter Gap Interleaved Bar CodeProgramming Mode Print Contrast SignalResolution Scanning ModeSymbol Length SymbolSymbology Substrate