Symbol Technologies WS 2000 manual Field Office Example

Page 126

A Field Office Example

He goes to the section labeled Access Port Adoption List and deselects the check boxes to the right of the row in which the MAC address range is specified as ANY.

For the engineering WLAN, Leo selects the Add button, then enters a Start MAC value of 00:A0:00:00:00:01 and an End MAC value of 00:A0:00:00:00:02. Leo selects the WLAN1 and makes sure that the other WLAN checkboxes are not checked.

To specify the marketing WLAN, Leo clicks again on the Add button. In the new line, he enters the same MAC address, 00:A0:00:00:00:03, for both the Start MAC and the End MAC. Leo selects the WLAN2 checkbox and makes sure that the other WLAN checkboxes are not checked.

Finally, for the administration WLAN, Leo again clicks the Add button. He enters 00:A0:00:00:00:04 as both the Start MAC and the End MAC address. He selects the WLAN3 checkbox and makes sure that the other WLAN checkboxes for that row are not selected.

Leo clicks the Apply button to save his changes.

The next step is to configure the WLANs.

Copyright © 2004 Symbol Technologies, Inc. All Rights Reserved	126
WS 2000 Wireless Switch: 1.0 Date of last Revision: March 2004

Image 126

Contents WS 2000 Wireless Switch Version System Reference72E-67701-01 Rev a March Copyright PatentsTable of Contents Chapter Advanced Configuration Chapter Field Office Example 111 WS 2000 Wireless Switch System Reference Guide About this DocumentDocument Conventions System Overview Management of Access PortsWireless LAN Wlan Security Firewall SecurityTechnical Specifications Physical SpecificationsHardware Overview Power Specifications Operating System OS ServicesCell Controller Services Environmental SpecificationsGateway Services 802.11a Support 802.11b SupportAccess Ports Gateway Services WS 2000 Wireless Switch FirewallNetwork Address Translation NAT Dhcp Client and Server Layer 3 RoutingSnmp Management Support Overview802.1x with Radius Authentication WEP 64 40-bit keyWEP 128 104-bit Key 802.1x with Shared Key Authentication Kerberos AuthenticationWireless Protected Access WPA KeyGuard-MCM SupportInstalling the Switch Set up Communication to the SwitchGetting Started Overview Getting Started Overview Changing the Administrator Password Configure the LAN Interface Configuring the SwitchDefining the Subnets Field DescriptionConfigure Subnets InterfacesDhcp Configuration Advanced Dhcp Settings Configure the WAN Interface Communicating with the Outside WorldSetting Up Point-to-Point over Ethernet PPPoE Communication Enable Wireless LANs WLANs ChapWireless Summary Area Configure WLANs Access Port AdoptionConfigure Wlan Security Field Description NameSubnet Setting the Authentication Method 802.1x EAP AuthenticationSetting the Encryption Method Kerberos AuthenticationConfiguring WEP Encryption Configuring WPA-TKIP Configure Wlan Security KeyGuard-MCM No EncryptionConfigure Access Ports Mobile Unit Access Control List ACLConfigure Access Ports Configure Subnet Access NameColor Access Type Description Green Access Overview TableAccess Exception Area YellowProtocol Transport Description Port Used HttpTransport Description ALLAdvanced Configuration WLAN-How to Configure Advanced SettingsWLAN-Setting Default Access Port Settings WLAN-Setting Default Access Port Settings Beacon Interval Dtim PeriodWLAN-Advanced Access Port Settings Primary WlanSecurity Beacon WLAN-Advanced Access Port Settings Beacon is a packet broadcast by the adopted access ports to Gateway-How to Configure Network Address Translation NAT Gateway-How to Configure Network Address Translation NAT Gateway-How to Configure the WS 2000 Firewall Always On Firewall FiltersConfigurable Firewall Filters Gateway-How to Configure Static Routes Mime Flood Attack CheckNo RIP Setting the RIP ConfigurationDefining Routes RIPCompat Security-How to Configure 802.1x EAP AuthenticationRIP v2 NoneSecurity-How to Configure 802.1x EAP Authentication Security-How to Configure 802.1x EAP Authentication Security-How to Configure Kerberos Authentication Security-How to Specify a Network Time Protocol NTP Server Overview Switch SettingsWS 2000 Wireless Switch LED Functions Location DescriptionChanging the Name of the Switch Change the Location and Country Settings of the WS Location fieldHow to Restart the WS 2000 Wireless Switch Updating the WS 2000 Wireless Switch’s FirmwareChecking for and Downloading Firmware updates Performing the Firmware UpdateSystem Configuration Exporting and Importing Wireless Switch SettingsTo Import or Export Settings to an FTP Site To Import Settings to a Local FileTo Export Settings to a Local File How to Restore Default Configuration Settings Property Value Setting the Snmp Version Configuration Remote AdministrationHow to Configure Snmp Traps Setting Up Snmp v1/v2c Community DefinitionsAuthNoPriv Setting Up Snmp v3 Community DefinitionsNoAuth AuthPrivSetting Up the Access Control List Setting the Trap ConfigurationTrap Trap Name Generates a Trap when… Category AuthenticationConfiguration Cold StartSetting the Trap Configuration for Snmp v1/v2c Configure Administrator Access Setting the Trap Configuration for SnmpConfigure Management Access Access Port DescriptionChanging the Administrator and Manager Passwords Access Port StatisticsSetup AirBEAM Software Access Statistics and LogsGeneral Access Port Information Received and Transmitted Tables Associated Mobile UnitsSubnet Statistics Received Field Description Transmitted Description FieldWAN Statistics InterfacesReceived Field Description Setting Up and Viewing the System Log Viewing the Log on the SwitchSetting Up a Log Server Retail Use Cases BackgroundPlan Configuring the System Settings Contacting the Wireless SwitchEntering the Basic System Settings Setting Access Control Configuring the Subnets IP Address PlanSubnet IP Address Range Configuring POS Subnet For each subnetConfiguring the Printer Subnet Retail Use Cases Configuring the Cafe Subnet Retail Use Cases Configuring the WAN Interface Configuring Network Address Translation NAT Retail Use Cases Switch Port Connected to Configuring the Access PortsSetting Access Port Defaults Inspecting the FirewallNaming the POS Access Port Configuring the Printer Access Port Configuring the Cafe Access Port Associating the Access Ports to the WLANs Configuring the WLANs Configuring the Cafe WlanConfiguring the Printer Wlan Name PrinterConfiguring the POS Wlan For the POS WLAN, she makes the following choicesSetting Subnet Access Retail Use Cases Wireless Authentication Encryption Channel Testing ConnectionsConfiguring the Clients Client IP Address Subnet Mask Gateway PortField Office Example Plan Configuring the System Settings Entering the Basic System Settings Setting Access Control Field Office Example Configuring the LAN Configuring the Engineering LANField Office Example Field Office Example Configuring the Sales Subnet Configuring the WAN Field Office Example Setting Up Network Address Translation Field Office Example MAC Address Location Confirm Firewall ConfigurationAdopting Access Ports Adoption List LabelField Office Example Configuring the WLANs Security Field Office Example Wlan Field Office Example Field Office Example Field Office Example Access Port Channel Configuring Subnet Access Installing the Access Ports and Testing Appendix A. Sample Configuration File NTP menu Wlan 1 configuration set mode 1 enable Wlan 3 configuration set mode 3 disable Default 802.11 a radio configuration set reg a in/out 149 Access Port configuration LAN Dhcp configuration network Firewall configuration set syn enable Outbound 1-To-Many NAT configuration set outb map s1 Page Index FTP Snmp 802.1x EAP authentication