Symbol Technologies WS 2000 manual Installing the Access Ports and Testing

Page 136

A Field Office Example

He could then enter the user-based or protocol-based restrictions in the EngSN --> WAN section.

Since Leo does not need to make any changes, there is nothing more to be done.

Installing the Access Ports and Testing

The switch is now configured! Leo connects the switch’s WAN port to the VPN appliance that goes to the outside world. He gets three laptops and sets each of them to use DHCP for IP address assignment, 802.1x EAP for user authentication, and WPA-TKIP for data encryption over the wireless link. He uses the first laptop to connect to the engineering WLAN, the second to connect to the sales and marketing WLAN, and the third laptop to connect to the administration WLAN. He makes sure that laptops on each WLAN can connect to the WAN and to each other.

After he has tested the three subnets, he installs the Access Ports in their permanent locations. He test coverage with the laptops, making sure each Access Port is covering its assigned area. He also unplugs each of the engineering Access Ports, in turn, to be sure that both are working properly. When everything seems to be working, he sends an email to the users telling them that the new wireless network is up and running!

Copyright © 2004 Symbol Technologies, Inc. All Rights Reserved	136
WS 2000 Wireless Switch: 1.0 Date of last Revision: March 2004

Image 136

Contents System Reference WS 2000 Wireless Switch Version72E-67701-01 Rev a March Copyright PatentsTable of Contents Chapter Advanced Configuration Chapter Field Office Example 111 About this Document WS 2000 Wireless Switch System Reference GuideDocument Conventions Management of Access Ports Wireless LAN Wlan SecuritySystem Overview Firewall SecurityPhysical Specifications Technical SpecificationsHardware Overview Operating System OS Services Cell Controller ServicesPower Specifications Environmental SpecificationsGateway Services 802.11a Support 802.11b SupportAccess Ports WS 2000 Wireless Switch Firewall Gateway ServicesNetwork Address Translation NAT Layer 3 Routing Snmp Management SupportDhcp Client and Server OverviewWEP 64 40-bit key 802.1x with Radius AuthenticationWEP 128 104-bit Key 802.1x with Shared Key Authentication Kerberos AuthenticationWireless Protected Access WPA KeyGuard-MCM SupportSet up Communication to the Switch Installing the SwitchGetting Started Overview Getting Started Overview Changing the Administrator Password Configure the LAN Interface Configuring the SwitchDefining the Subnets Field DescriptionConfigure Subnets InterfacesDhcp Configuration Advanced Dhcp Settings Configure the WAN Interface Communicating with the Outside WorldSetting Up Point-to-Point over Ethernet PPPoE Communication Enable Wireless LANs WLANs ChapWireless Summary Area Configure WLANs Access Port AdoptionField Description Name Configure Wlan SecuritySubnet Setting the Authentication Method 802.1x EAP AuthenticationKerberos Authentication Setting the Encryption MethodConfiguring WEP Encryption Configuring WPA-TKIP Configure Wlan Security KeyGuard-MCM No EncryptionConfigure Access Ports Mobile Unit Access Control List ACLConfigure Access Ports Configure Subnet Access NameAccess Overview Table Access Exception AreaColor Access Type Description Green YellowProtocol Transport Description Port Used HttpTransport Description ALLAdvanced Configuration WLAN-How to Configure Advanced SettingsWLAN-Setting Default Access Port Settings WLAN-Setting Default Access Port Settings Beacon Interval Dtim PeriodPrimary Wlan WLAN-Advanced Access Port SettingsSecurity Beacon WLAN-Advanced Access Port Settings Beacon is a packet broadcast by the adopted access ports to Gateway-How to Configure Network Address Translation NAT Gateway-How to Configure Network Address Translation NAT Gateway-How to Configure the WS 2000 Firewall Always On Firewall FiltersConfigurable Firewall Filters Gateway-How to Configure Static Routes Mime Flood Attack CheckSetting the RIP Configuration Defining RoutesNo RIP RIPSecurity-How to Configure 802.1x EAP Authentication RIP v2Compat NoneSecurity-How to Configure 802.1x EAP Authentication Security-How to Configure 802.1x EAP Authentication Security-How to Configure Kerberos Authentication Security-How to Specify a Network Time Protocol NTP Server Switch Settings WS 2000 Wireless Switch LED FunctionsOverview Location DescriptionChanging the Name of the Switch Change the Location and Country Settings of the WS Location fieldHow to Restart the WS 2000 Wireless Switch Updating the WS 2000 Wireless Switch’s FirmwareChecking for and Downloading Firmware updates Performing the Firmware UpdateSystem Configuration Exporting and Importing Wireless Switch SettingsTo Import Settings to a Local File To Import or Export Settings to an FTP SiteTo Export Settings to a Local File How to Restore Default Configuration Settings Property Value Remote Administration How to Configure Snmp TrapsSetting the Snmp Version Configuration Setting Up Snmp v1/v2c Community DefinitionsSetting Up Snmp v3 Community Definitions NoAuthAuthNoPriv AuthPrivSetting Up the Access Control List Setting the Trap ConfigurationAuthentication ConfigurationTrap Trap Name Generates a Trap when… Category Cold StartSetting the Trap Configuration for Snmp v1/v2c Configure Administrator Access Setting the Trap Configuration for SnmpConfigure Management Access Access Port DescriptionAccess Port Statistics Setup AirBEAM Software AccessChanging the Administrator and Manager Passwords Statistics and LogsGeneral Access Port Information Received and Transmitted Tables Associated Mobile UnitsSubnet Statistics Received Field Description Transmitted Description FieldWAN Statistics InterfacesReceived Field Description Setting Up and Viewing the System Log Viewing the Log on the SwitchSetting Up a Log Server Retail Use Cases BackgroundPlan Configuring the System Settings Contacting the Wireless SwitchEntering the Basic System Settings Setting Access Control IP Address Plan Configuring the SubnetsSubnet IP Address Range Configuring POS Subnet For each subnetConfiguring the Printer Subnet Retail Use Cases Configuring the Cafe Subnet Retail Use Cases Configuring the WAN Interface Configuring Network Address Translation NAT Retail Use Cases Configuring the Access Ports Setting Access Port DefaultsSwitch Port Connected to Inspecting the FirewallNaming the POS Access Port Configuring the Printer Access Port Configuring the Cafe Access Port Associating the Access Ports to the WLANs Configuring the WLANs Configuring the Cafe WlanConfiguring the Printer Wlan Name PrinterConfiguring the POS Wlan For the POS WLAN, she makes the following choicesSetting Subnet Access Retail Use Cases Testing Connections Configuring the ClientsWireless Authentication Encryption Channel Client IP Address Subnet Mask Gateway PortField Office Example Plan Configuring the System Settings Entering the Basic System Settings Setting Access Control Field Office Example Configuring the LAN Configuring the Engineering LANField Office Example Field Office Example Configuring the Sales Subnet Configuring the WAN Field Office Example Setting Up Network Address Translation Field Office Example Confirm Firewall Configuration Adopting Access PortsMAC Address Location Adoption List LabelField Office Example Configuring the WLANs Security Field Office Example Wlan Field Office Example Field Office Example Field Office Example Access Port Channel Configuring Subnet Access Installing the Access Ports and Testing Appendix A. Sample Configuration File NTP menu Wlan 1 configuration set mode 1 enable Wlan 3 configuration set mode 3 disable Default 802.11 a radio configuration set reg a in/out 149 Access Port configuration LAN Dhcp configuration network Firewall configuration set syn enable Outbound 1-To-Many NAT configuration set outb map s1 Page Index FTP Snmp 802.1x EAP authentication