SonicWALL E6500 manual Accessing the Management Interface, Accessing the Setup Wizard

Page 27

Accessing the Management Interface

The computer you use to manage the SonicWALL NSA E6500 must be set up to accept a dynamic IP address, or it must have an unused IP address on the 192.168.168.x/24 subnet, such as 192.168.168.20.

To access the SonicOS Enhanced Web-based management interface:

1.Start your Web browser.

Note: Disable pop-up blocking software or add the management IP address http://192.168.168.168 to your pop-up blocker’s allow list.

2.Enter http://192.168.168.168 (the default LAN management IP address) in the Location or Address field.

3.The SonicWALL Setup Wizard launches and guides you through the configuration and setup of your SonicWALL NSA E6500.

The Setup Wizard launches upon initial loading of the SonicWALL NSA E6500 management interface.

4.Follow the on-screen prompts to complete the Setup Wizard.

Depending on the changes made during your setup configuration, the SonicWALL may restart.

Accessing the Setup Wizard

If you cannot connect to the SonicWALL NSA E6500 or the Setup Wizard does not display, verify the following configurations:

Did you correctly enter the SonicWALL NSA E6500 management IP address in your Web browser?

Are the Local Area Connection settings on your computer set to use DHCP or set to a static IP address on the 192.168.168.x/24 subnet?

Do you have the Ethernet cable connected to your computer and to the X0 (LAN) port on your SonicWALL?

Is the connector clip on your network cable properly seated in the port of the security appliance?

Some browsers may not launch the Setup Wizard automatically. In this case:

Log into SonicWALL NSA E6500 using “admin” as the user name and “password” as the password.

Click the Wizards button on the System > Status page.

Select Setup Wizard and click Next to launch the Setup Wizard.

Some pop-up blockers may prevent the launch of the Setup Wizard. You can temporarily disable your pop- up blocker, or add the management IP address of your SonicWALL (192.168.168.168 by default) to your pop- up blocker's allow list.

Page 26 Initial Setup

Image 27
Contents NSA E6500 Getting Started Guide SonicWALL NSA E6500 Document ContentsSonicWALL NSA E6500 FrontThis Section Pre-Configuration TasksCheck Package Contents Registration Information Obtain Configuration InformationAdministrator Information Obtain Internet Service Provider ISP InformationLCD Screen Front PanelBack Panel LCD Control Buttons Front Bezel Control FeaturesStatus Main MenuConfigure Screen-Saver Configuration OptionsRestart SafeModeLAN IP Configuration Front Bezel Configuration ExampleRegistering Your Appliance Before You Register Product Registration Registering and Licensing Your Appliance on mysonicwall.comGateway Services Licensing Security Services and SoftwareSonicWALL NSA E6500 Getting Started Guide Registration Next Steps Registering a Second Appliance as a BackupDeployment Scenarios Selecting a Deployment Scenario ABCScenario a NAT/Route Mode Gateway Scenario B State Sync Pair in NAT/Route Mode Scenario C L2 Bridge Mode Initial Setup Connecting the WAN PortSystem Requirements Applying Power Connecting the LAN PortAccessing the Setup Wizard Accessing the Management InterfaceTesting Your Connection Connecting to Your NetworkActivating Licenses in SonicOS Saving a Backup Copy of Your Preferences Upgrading Firmware on Your SonicWALLObtaining the Latest Firmware Upgrading the Firmware Using SafeMode to Upgrade FirmwareAdditional Deployment Initial High Availability Setup Configuring a State Sync Pair in NAT/Route ModeConfiguring Advanced HA Settings Configuring High Availability34 Configuring a State Sync Pair in NAT/Route Mode Synchronizing Settings Synchronizing Firmware Adjusting High Availability SettingsYour Appliance on mysonicwall.com HA License Configuration OverviewAssociating Pre-Registered Appliances Configuring L2 Bridge Mode Configuring the Primary Bridge InterfaceConnection Overview IP Assignment drop-down, select Layer 2 Bridged Mode Configuring the Secondary Bridge InterfaceAdditional Deployment Configuration An Introduction to Zones and Interfaces Creating Network Access RulesSonicWALL NSA E6500 Getting Started Guide 44 Creating Network Access Rules Creating a NAT Policy Configuring Address Objects Configuring NAT Policies Enabling Security Services in SonicOS Applying Security Services to ZonesGateway Anti-Virus Intrusion Prevention Anti-Spyware Using Packet Capture Troubleshooting Diagnostic ToolsUsing Ping Using the Active Connections Monitor Using Log View For this Task See this Chapter Deployment Configuration Reference Checklist54 Deployment Configuration Reference Checklist Support and Training Options Knowledge Portal Customer SupportUser Forums Training Related Documentation SonicWALL Live Product Demos Dynamic TooltipsSonicWALL NSA E6500 Getting Started Guide 62 SonicWALL Live Product Demos Rack Mounting Instructions Rack Mounting Instructions SSEMBLEMTHEL3LIDET2AIL  &ASTEN TWOSIDEDISCREWSWTOOTHETRAIL SSEMBLEMNNERE2AILITOO#HASSIS NSERTT#HASSISATOO&RAME  3LIDEIINNER CHANNELEINTOORAILS 68 Rack Mounting Instructions Product Safety and Regulatory Information Rack Mounting the SonicWALL Safety and Regulatory InformationHinweis zur Lithiumbatterie FCC Part 15 Class a Notice Trademarks Copyright NoticePage SonicWALL NSA E6500 Getting Started Guide Page Protection AT the Speed of Business