SMC Networks SMC7824M/ESW manual Optional Media Extender Module, 1000BASE Combo Module

Page 29

OPTIONAL MEDIA EXTENDER MODULE

Optional Media Extender Module

1000BASE Combo Module

Figure 1-5 Single-Port 1000BASE-T/SFP Combo Module

The 1000BASE-T RJ-45 port and SFP slot on this module share the same internal interface. If an SFP transceiver (purchased separately) is installed in a slot and has a valid link, the associated RJ-45 port is disabled and cannot be used. The switch can also be configured to force the use of an RJ-45 port or SFP slot, as required.

When connecting to the 1000BASE-T RJ-45 port, Category 5, 5e, or 6 twisted-pair cable can be used to connect to another device up to 100 m (328 ft) away. The 1000BASE-T port operates at 10, 100, and 1000 Mbps. At 1000 Mbps it operates at full duplex and supports auto-negotiation of flow control. At 10/100 Mbps it supports auto-negotiation of speed, duplex mode (i.e., half or full duplex), and flow control. Note that you should first test the cable installation for IEEE 802.3ab compliance. See “1000BASE-T Cable Requirements” on page 4-6.

This module also provides an SFP slot that supports 1000BASE-SX, 1000BASE-LX and 1000BASE-ZX transceivers. For a full listing of the supported transceivers, see “Ordering Information” on page E-1.

1-9

Image 29

Contents TigerAccess 10/100 Page TigerAccess 10/100 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA FCC Class a CompliancesIndustry Canada Class a Japan Vcci Class aViii CE Mark Declaration of Conformance for EMI and Safety EECWarnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceAustralia AS/NZS 3548 1995 Class a Power Cord Set Power Cord SafetyFrance et Pérou uniquement Xii PSE AlarmXiii Xiv Table of Contents Xvi Making Network ConnectionsSpecifications TroubleshootingCables German InstructionsXviii Xix TablesFigures Overview Chapter About Tigeraccess SwitchNetwork Management Options Switch Architecture100BASE-TX Management Port Description of Hardware100BASE-TX and 1000BASE-T Ports Optional SFP Transceivers Console PortSFP Slots Port and System Status LEDs Alarm Interface PortLED Port and System Status LEDsFan Tray Fan TrayOptional Power Modules Power Modules1000BASE Combo Module Optional Media Extender ModuleConnectivity Features and BenefitsExpandability PerformanceManagement About the Tigeraccess Switch Application Examples Introduction to SwitchingChapter Network Planning Collapsed Backbone Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Selecting a Site Installing the SwitchRJ-45 Connections Ethernet CablingOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Rack Mounting MountingInstalling the Switch in a Rack Attaching the Adhesive Feet Desktop or Shelf MountingInstalling an Optional Module Installing an Optional Module into the SwitchInserting an SFP Transceiver into a Slot Installing an Optional SFP TransceiverGrounding the Chassis Connecting DC Power Connecting to a Power SourceConnecting to a Power Source DC Plug Connections AC Power Receptacle Connecting AC PowerSerial Cable Wiring Connecting to the Console PortWiring Map for Serial Cable 10 Alarm Port D-15 Pin-Out Connecting to the Alarm PortAlarm Cable Wiring Wiring Map for Alarm Cable11 External Alarm I/O Connections Installing the Switch Chapter Making Network Connections Connecting Network DevicesTwisted-Pair Devices Cabling GuidelinesMaking Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesNetwork Wiring Connections Network Wiring ConnectionsFiber Optic SFP Devices Making Connections to SFP Transceivers 1000BASE-T Cable Requirements Connectivity RulesMbps Gigabit Ethernet Cable Lengths Maximum 1000BASE-T Gigabit Ethernet Cable LengthMbps Ethernet Cable Lengths Mbps Fast Ethernet Cable LengthsCable Labeling and Connection Records Table A-1 Diagnosing Switch Indicators Appendix a TroubleshootingDiagnosing Switch Indicators Troubleshooting In-Band Access Power and Cooling ProblemsInstallation Troubleshooting Twisted-Pair Cable and Pin Assignments Appendix B CablesTable B-1 10/100BASE-TX MDI and MDI-X Port Pinouts 10BASE-T/100BASE-TX Pin AssignmentsFigure B-2 Straight-through Wiring Straight-Through WiringFigure B-3 Crossover Wiring Crossover WiringTable B-2 1000BASE-T MDI and MDI-X Port Pinouts 1000BASE-T Pin AssignmentsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Cable Testing for Existing Category 5 CableFiber Standards Cables Physical Characteristics Appendix C SpecificationsWeight Switching DatabaseTemperature Power SupplyManagement Features Switch FeaturesCompliances StandardsEmissions ImmunityExtender Modules Extender Modules Eine Site Auswählen Selecting a Site Appendix D German InstructionsRack-Montage Montage Rack Mounting InstructionsGrounding the Chassis Das Erden des GehäusesAnschluss an Gleichstrom Anschluss an eine StromquelleAnschluss AN Eine Stromquelle Connecting to a Power Source Figure D-1 Gleichstromanschlüsse Wechselstromanschluss Figure D-2 Wechselstromanschluss Appendix E Ordering Information Table E-1 TigerAccess 10/100 Products and AccessoriesOrdering Information Glossary-1 Glossary1000BASE-T Auto-NegotiationGlossary-2 Glossary-3 Glossary-4 Virtual LAN Vlan Glossary-5Transmission Control Protocol/Internet Protocol TCP/IP Glossary-6 Index-1 IndexIndex-2 SFP Index-3Index-4 Page For Technical SUPPORT, Call