SMC Networks SMC8124PL2 manual France et Pérou uniquement

Page 10

Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following:

Power Cord Set

U.S.A. and Canada	The cord set must be UL-approved and CSA certified.

	The minimum specifications for the flexible cord are:
	- No. 18 AWG - not longer than 2 meters, or 16 AWG.
	- Type SV or SJ
	- 3-conductor

	The cord set must have a rated current capacity of at least 10 A

	The attachment plug must be an earth-grounding type with NEMA 5-15P (15 A,
	125 V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark	The supply plug must comply with Section 107-2-D1, Standard DK2-1a or
	DK2-5a.

Switzerland	The supply plug must comply with SEV/ASE 1011.

U.K.	The supply plug must comply with BS1363 (3-pin 13 A) and be fitted with a 5 A
	fuse which complies with BS1362.

	The mains cord must be <HAR> or <BASEC> marked and be of type
	HO3VVF3GO.75 (minimum).

Europe	The supply plug must comply with CEE7/7 (“SCHUKO”).

	The mains cord must be <HAR> or <BASEC> marked and be of type
	HO3VVF3GO.75 (minimum).

	IEC-320 receptacle.

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch:

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié.

•Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse).

•Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité.

•Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit respecter une configuration qui permet un branchement sur une entrée d’appareil EN 60320/IEC 320.

•La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique au niveau de cette prise.

•L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il est raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

x

Image 10

Contents Installation Guide Installationsanleitung Page TigerSwitch 10/100/1000 Installation Guide Page Limited Warranty SMC Networks, Inc Mason Irvine, CA Compliances and Safety Warnings ViiCE Mark Declaration of Conformance for EMI and Safety EEC ViiiSafety Compliance Warnhinweis Faseroptikanschlüsse Optische SicherheitFrance et Pérou uniquement No pour un cable de longueur inférieure à 2 métres Xii Documentation End of Product Life SpanManufacturing Materials XiiiXiv Contents Contents Making Network ConnectionsContents Xviii Tables Figures Switch Architecture About the TigerSwitch 10/100/1000Overview Description of Hardware Power-over-Ethernet CapabilityAbout the TigerSwitch 10/100/1000 Network Management OptionsPort and System Status LEDs SFP SlotsCondition Status Connectivity Features and BenefitsPower Supply Socket System Status LEDsPerformance ExpandabilityManagement About the TigerSwitch 10/100/1000 Application Examples Introduction to SwitchingNetwork Planning Collapsed BackboneNetwork Aggregation Plan Network PlanningRemote Connections with Fiber Cable Making Vlan ConnectionsApplication Notes Making Vlan ConnectionsSelecting a Site Installing the SwitchEthernet Cabling Package Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingMounting Installing the Switch in a Rack Desktop or Shelf MountingInstalling an SFP Transceiver Inserting an SFP Transceiver into a SlotConnecting to a Power Source Connecting to the Console PortSerial Cable Wiring Switch’s 9-Pin Null Modem PC’s 9-Pin Wiring Map for Serial CableDTE Port Installing the Switch Making Network Connections Connecting Network DevicesPower-over-Ethernet Connections Twisted-Pair DevicesNetwork Wiring Connections Connecting to PCs, Servers, Hubs and SwitchesMaking Network Connections Wiring Closet Connections Fiber Optic SFP DevicesMaking Connections to SFP Transceivers 1000BASE-T Cable Requirements Connectivity RulesMbps Gigabit Ethernet Collision Domain Mbps Fast Ethernet Collision Domain Cable Labeling and Connection RecordsMbps Ethernet Collision Domain Cable Labeling and Connection Records Making Network Connections Power and Cooling Problems Appendix a TroubleshootingDiagnosing Switch Indicators InstallationIn-Band Access TroubleshootingTwisted-Pair Cable and Pin Assignments Appendix B Cables10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring CablesTwisted-Pair Cable and Pin Assignments B Crossover Wiring1000BASE-T Pin Assignments Table B-2 1000BASE-T MDI and MDI-X Port PinoutsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Cable Testing for Existing Category 5 CableFiber Standards Appendix C Specifications Physical CharacteristicsSpecifications Switch FeaturesManagement Features StandardsCompliances WarrantyCompliances C Specifications Eine Site Auswählen Selecting a Site Appendix D German InstructionsRack-Montage German Instructions Appendix E Ordering Information SMC1GSFP-ZXOrdering Information Glossary Glossary-1Glossary Glossary-2Ieee 802.3z Glossary-3TIA Glossary-4Index Index-1Index Index-2Page SMC8124PL2