SMC Networks SMC6608T, SMC6608M manual Basic Port Settings

Page 55

CONFIGURATION AND MANAGEMENT

Basic Port Settings

When using the Configure button to set port communication modes:

1.Use a long press (>2 seconds) to begin function selection. The Status LED will start to flash to indicate that functions may be selected. Use short presses (<2 seconds) to cycle through the status LEDs until the Full/Half LED lights. Use a long press to initiate port communication mode selection. After the button is released, the Full-DuplexLED for Port 1 will begin to flash.

2.Use long presses to cycle through to the chosen port. The selection of the targeted port will be indicated by the lighting of the Tx/Rx LED for that port.

3.Use a short press to change the communication mode for the targeted port. The chosen mode will be indicated by the Full-DuplexLED for the port (Lit = Full*, Unlit = Half).

4.Use a long press to enable the selection.

5.Repeat Steps 2 through 4 for each chosen port.

The default communication mode setting for all ports is Auto- Negotiation, which dynamically selects either half- or full-duplex mode and 10 or 100 Mbps operating speed in response to the operating mode of the attached device. Auto-Negotiation can be re-established after a manual port configuration by removing the RJ-45 connector from the corresponding port on the switch and then reinserting it.

*Note: Full-duplex mode can be used only for a dedicated link. When connecting to a shared collision domain (e.g., a hub), be sure the transmission mode is set for half-duplex mode.

4-4

Image 55

Contents TigerSwitch User Guide TigerSwitch Trademarks Limited Warranty Limited Warranty Table of Contents Pin Assignments TroubleshootingSpecifications AppendicesIii List of FiguresTable of Contents Industry Canada Class a CompliancesFCC Class a EC Conformance DeclarationCompliances Japan Vcci Class a Australia AS/NZS 3548 1995 Class aWichtige Sicherheitshinweise ViiViii Chapter About Tigerswitch About the Tigerswitch TigerSwitch 100 Overview TigerSwitch 100M Base Unit Model SMC6608M Port Fast Ethernet Modules for Model SMC6608M Module Ports Connectors Description10BASE-T/100BASE-TX Ports Switch Ports100BASE-FX Ports SMC6608M only Front Panel LEDs Status LEDsConsole Port Configure ButtonPower Supply Receptacles Optional Redundant Power UnitRedundant Power Units RPUs Switching Methods Switch ArchitectureSpanning Tree Protocol Serial Console Port Management OptionsTelnet Connectivity Key Features and BenefitsPerformance Practical Management Easy InstallationChapter Planning Introduction to Switching Collapsed Backbone Sample ApplicationsMultiple Port Bridging Connections Multiport BridgingServer Farm Connectivity and Expansion Server Farm AggregationCascading to a Fast Ethernet Switch High-Speed Switch LinksCollapsed Backbone with Fiber Cable Collapsed Backbone Using Fiber CableHigh-Speed Fiber Backbone High-Speed Fiber BackboneApplication Notes Page Chapter Installation Selecting a Site Package Contents Equipment ChecklistRequired Rack-Mounting Equipment Mounting Mounting the Switch in a RackAttaching the Brackets Attaching the Adhesive Feet Mounting and Stacking the Switch on a Flat SurfaceConnecting to a Power Source Powering UpDiagnostics SMC 5 4 3 Rule Making Network ConnectionsConnectivity Rules Mbps Ethernet Collision DomainMaximum 100BASE-T Network Diameter Mbps Fast Ethernet Collision DomainSMC 3 2 Rule for Class II Repeaters SMC 2 1 Rule for Class I and Class II RepeatersTwisted-Pair Cabling Guidelines Fixed Crossover Ports Connecting 10BASE-T/100BASE-TX PortsDaisy-Chain Port Fiber Cable Connectors Connecting 100BASE-FX PortsPage Chapter Configuration Management Configuration and Management Configuration Options Basic Port Settings Required Connections and Switch Access Advanced System ConfigurationSnmp Network Connection In-Band Connections TelnetLogin System Configuration ProgramMain Menu Main MenuDownload & Reset ConfigurationPassword Configuration Setting PasswordsConsole Configuration Console Port ConfigurationSystem Configuration System Parameter ConfigurationConfiguration and Management Port Configuration Screen Port ConfigurationConfiguration and Management Spanning Tree Configuration Yes Spanning Tree ConfigurationPort Priority Path Cost Configuration and Management Virtual LAN Configuration Screen Virtual LAN ConfigurationSystem Monitoring Monitoring via the Configure Button and LEDsLEDs Functions Status LEDsSystem Information Advanced System MonitoringSystem Information Port Status Statistics StatisticsStatistics Screen Items Address Table Address TableCurrent Spanning Tree Information Spanning Tree InformationPort State DesignatedCost DesignatedBridgeID DesignatedPort Parameter Description Spanning Tree Information Screen ItemsDownloading via Tftp Protocol Downloading System SoftwareTftp Download Downloading via the Console Port Reset Resetting the SwitchChapter Management VIA Snmp Snmp Protocol MIB Objects Assigning Snmp Agent Access Rights Snmp Parameter ConfigurationSnmp Configuration Community Strings Community Strings ScreenTrap Receivers Trap Receivers ScreenAppendix a Troubleshooting Switch Indicators System Failures Diagnostic TestsSystem Diagnostic Tests Component Failure LED Array Indicator ColumnPort Failures Test Failure LED Array Row System DiagnosticsPort Diagnostic Tests Power and Cooling ProblemsNetwork Cards Communication ModePhysical Configuration CablingTerminal Emulation Management InterfaceSystem Integrity Page Appendix B PIN Assignments RJ-45 Pin Assignments Pin Number Assignment RJ-45 Pin AssignmentsCrossover RJ-45 Pin Assignments End Straight-Through WiringCrossover Wiring Straight-Through RJ-45 Pin Assignments EndDCE Console Port Pin AssignmentsConsole Port to 25-Pin DCE Port on Modem Switch Port PC Port DB-9 Pin No SignalSwitch Port Pin Modem Port DB-9 Pin No Signal Console Port to 9-Pin COM Port on PCConsole Port to 25-Pin DTE Port on PC Switch Port DB-9 Pin NoNull Modem Pin PC Port Appendix C Specifications All Models EMC/Safety Compliances Input PowerPower Consumption Operating TemperatureModel SMC6608M Model SMC6608T100BASE-FX Page Appendix D Glossary ANSI/IEEE 802.3u Standard ANSI/IEEE 802.3 StandardEthernet CollisionCrossover Port End StationIn-Band Media Access Control MACRJ-45 Connector Icmp Internet Control Message ProtocolUTP Unshielded Twisted-Pair TerminatorSimple Network Management Protocol Snmp Straight-through PortPublication Number 900.168, Rev. B