SMC Networks Ethernet ISA Network Cards manual Changing the Settings, Medium Type, Full Duplex

Page 20

HARDWARE SETTINGS

Changing the Settings

The following settings may be changed in the Plug and Play and Jumperless environments.

Medium Type

The transceiver setting depends on the type of card you are using. It should agree with the network cabling type. For combo cards, this program provides two media type selections: Auto Detect and AUI.

If you are using the RJ-45 or BNC connector, you can select “Auto Detect” to have the system automatically determine the media type (i.e., 10BASE-T or 10BASE2). If you are using an AUI connection, then specify 10BASE5 (AUI).

Full Duplex

Enable full-duplex mode only if the card is connected directly to a switch that also supports this mode. Do not enable this mode if the card is connected to a hub.

I/O Base Address (Jumperless Environment only)

Select any available address in the range 200h to 3E0h from the displayed list. The factory default is 300h. The following table represents the most commonly used I/O Base Addresses:

I/O Base

Potential Conflicting Devices and

Addresses

their Typical I/O Addresses

 

 

300

NE2000 default setting

 

 

320

XT Hard Disk Interface (320 to 32F)

 

 

360

LPT1: (378 to 37F) +

 

 

Table 2.1. Commonly Used I/O Base Addresses

2-3

Page 19 Page 21
Image 20
Page 19 Page 21
Contents EZ Card User Guide For SMC’s EZ Card ISA Network Card Trademarks EZ Card 10 ISA Models About this GuideOrder Number Description Package Contents Quick Start Installing the CardConfiguring the Card Program Menu Vii Viii Software Installation NetWare Client Operating SystemSoftware Installation Screen Other Operating Systems Including Windows95 and NTQuick Start Table of Contents Specifications Glossary Index Limited Warranty CompliancesList of Figures List of TablesLAN Connectors Chapter Hardware DescriptionLink Status Lnk Activity Status ACTChapter Hardware Settings Default SetupManual Setup Manual Setup Plug and Play EnvironmentChanging the Settings Medium TypeFull Duplex Base Address Jumperless Environment onlyCommonly Used IRQ Channels Boot ROMInterrupt Jumperless Environment only Commonly Used Memory Addresses Appendix a Diagnostics Figure A-1. Main MenuFigure A-2. On-Board Diagnostics Diagnose the CardNetwork Diagnostics Figure A-3. Eeprom TestFigure A-5. On-Network Diagnostics Initiator Screen Appendix B Troubleshooting Clean BootProblems and Solutions SymptomsPossible Cause SuggestionsSymptom Possible CausesRJ-45 Connector Table C-1. RJ-45 Connector Pin AssignmentsAppendix C PIN Assignments Pin Number AssignmentAUI Connector Table C.2. AUI Connector Pin AssignmentsAppendix D Specifications GeneralEMC/Safety Compliance Operating TemperaturePower Requirements Operating EnvironmentNetwork Drivers AUI Attachment Unit Interface Boot ROMAppendix E Glossary Broadcast CollisionDriver FrameUnshielded Twisted-Pair Cable UTP RJ-45 ConnectorNetWare Index Index Limited Warranty Limited Warranty Cdoc Class B CompliancesFCC Class B EC Conformity Vcci Class B Australia AS/NZS 3548Printed on recycled paper

Ethernet ISA Network Cards specifications

SMC Networks, known for its innovative networking solutions, produced Ethernet ISA network cards that made significant contributions to the realm of computer networking during the late 20th century. These cards represented a pivotal development in the transition from traditional networking to more modern, high-speed connections, catering to the needs of both businesses and home users.

One of the main features of SMC Networks Ethernet ISA network cards was their ability to provide a reliable wired connection using the Industry Standard Architecture (ISA) bus. This interface facilitated an easy installation process on compatible devices, ensuring plug-and-play capabilities and broad compatibility with various operating systems available at the time, such as DOS and early versions of Windows. Users appreciated the straightforward setup process, which allowed even less technical individuals to integrate networking functions into their computers seamlessly.

SMC's Ethernet ISA network cards typically supported a data transmission rate of 10 Mbps, which was the standard speed for Ethernet technology during their prime. This speed, while modest by today’s standards, represented a significant improvement over older serial and parallel communication methods, allowing for faster file transfers and improved networking capabilities among connected devices.

The cards also featured an onboard 12-pin connector for attaching an external transceiver, supporting twisted pair cabling and coaxial connections. This versatility allowed users to choose their preferred cabling solutions based on their specific network environment. Furthermore, the Ethernet ISA cards supported the CSMA/CD protocol, which effectively managed data collisions in a shared network environment, enhancing the reliability and efficiency of data transmission.

Durability and robust design characterized SMC Networks’ approach to network card manufacturing. The cards were built to withstand the demands of various operating environments, ensuring stable performance over extended periods. Additionally, the compatibility with several popular networking protocols made these cards suitable for a broad range of applications, from simple peer-to-peer networks to more complex enterprise systems.

Overall, SMC Networks Ethernet ISA network cards played a crucial role in evolving networking technologies. Their reliable performance, ease of installation, and compatibility made them a valuable asset for organizations and individuals looking to harness the power of computer networking effectively. As technology advanced, these cards paved the way for the development of faster and more sophisticated networking solutions that we rely on today.
Top Page Image Contents