SMC Networks Ethernet ISA Network Cards Quick Start, Installing the Card, Configuring the Card

Page 6

QUICK START

Installing the Card

1.Power off your PC and remove its cover.

2.If you have purchased an optional boot ROM, plug the boot ROM into the socket on the card, making sure the notch on the memory device and that on the socket are in the same direction.

3.Select an available expansion slot and plug in the card.

4.Connect your card using the appropriate network connection (RJ-45, BNC or AUI).

5.Power on the PC.

6.Follow the appropriate instructions in this chapter to configure the card and load the network drivers.

Configuring the Card

Important: It is recommended that you read the RELEASE.TXT file located on the driver diskette. This file provides information about the disk’s contents. The contents of the file is displayed by typing the following command at the DOS prompt:

TYPE RELEASE.TXT Press <Enter>

To install and run the configuration program, proceed as follows:

1.Insert the driver diskette in drive A: or B:

2.Type the following command at the DOS prompt:

INSTALL <PATH> Press <Enter>

where: <PATH> is the directory location where you wish to install the program.

v

Page 5 Page 7
Image 6
Page 5 Page 7
Contents EZ Card User Guide For SMC’s EZ Card ISA Network Card Trademarks About this Guide Order Number DescriptionEZ Card 10 ISA Models Package Contents Installing the Card Configuring the CardQuick Start Program Menu Vii Viii Software Installation NetWare Client Operating SystemSoftware Installation Screen Other Operating Systems Including Windows95 and NTQuick Start Table of Contents Specifications Glossary Index Limited Warranty CompliancesList of Figures List of TablesLAN Connectors Chapter Hardware DescriptionLink Status Lnk Activity Status ACTChapter Hardware Settings Default SetupManual Setup Manual Setup Plug and Play EnvironmentFull Duplex Changing the SettingsMedium Type Base Address Jumperless Environment onlyBoot ROM Interrupt Jumperless Environment onlyCommonly Used IRQ Channels Commonly Used Memory Addresses Appendix a Diagnostics Figure A-1. Main MenuFigure A-2. On-Board Diagnostics Diagnose the CardNetwork Diagnostics Figure A-3. Eeprom TestFigure A-5. On-Network Diagnostics Initiator Screen Appendix B Troubleshooting Clean BootPossible Cause Problems and SolutionsSymptoms SuggestionsSymptom Possible CausesAppendix C PIN Assignments RJ-45 ConnectorTable C-1. RJ-45 Connector Pin Assignments Pin Number AssignmentAUI Connector Table C.2. AUI Connector Pin AssignmentsAppendix D Specifications GeneralPower Requirements EMC/Safety ComplianceOperating Temperature Operating EnvironmentNetwork Drivers Boot ROM Appendix E GlossaryAUI Attachment Unit Interface Driver BroadcastCollision FrameRJ-45 Connector NetWareUnshielded Twisted-Pair Cable UTP Index Index Limited Warranty Limited Warranty Compliances FCC Class BCdoc Class B EC Conformity Vcci Class B Australia AS/NZS 3548Printed on recycled paper

Ethernet ISA Network Cards specifications

SMC Networks, known for its innovative networking solutions, produced Ethernet ISA network cards that made significant contributions to the realm of computer networking during the late 20th century. These cards represented a pivotal development in the transition from traditional networking to more modern, high-speed connections, catering to the needs of both businesses and home users.

One of the main features of SMC Networks Ethernet ISA network cards was their ability to provide a reliable wired connection using the Industry Standard Architecture (ISA) bus. This interface facilitated an easy installation process on compatible devices, ensuring plug-and-play capabilities and broad compatibility with various operating systems available at the time, such as DOS and early versions of Windows. Users appreciated the straightforward setup process, which allowed even less technical individuals to integrate networking functions into their computers seamlessly.

SMC's Ethernet ISA network cards typically supported a data transmission rate of 10 Mbps, which was the standard speed for Ethernet technology during their prime. This speed, while modest by today’s standards, represented a significant improvement over older serial and parallel communication methods, allowing for faster file transfers and improved networking capabilities among connected devices.

The cards also featured an onboard 12-pin connector for attaching an external transceiver, supporting twisted pair cabling and coaxial connections. This versatility allowed users to choose their preferred cabling solutions based on their specific network environment. Furthermore, the Ethernet ISA cards supported the CSMA/CD protocol, which effectively managed data collisions in a shared network environment, enhancing the reliability and efficiency of data transmission.

Durability and robust design characterized SMC Networks’ approach to network card manufacturing. The cards were built to withstand the demands of various operating environments, ensuring stable performance over extended periods. Additionally, the compatibility with several popular networking protocols made these cards suitable for a broad range of applications, from simple peer-to-peer networks to more complex enterprise systems.

Overall, SMC Networks Ethernet ISA network cards played a crucial role in evolving networking technologies. Their reliable performance, ease of installation, and compatibility made them a valuable asset for organizations and individuals looking to harness the power of computer networking effectively. As technology advanced, these cards paved the way for the development of faster and more sophisticated networking solutions that we rely on today.
Top Page Image Contents