SMC Networks SMC2804WBR V.2 manual 10/100 LED does not light after a connection is made

Page 83

Troubleshooting

2.Type ipconfig/release.

3.Then type ipconfig/renew.

D. The 10/100 LED does not light after a connection is made

1.Check that the host computer and the Wireless Barricade™ are both powered on.

2.Be sure the network cable is connected to both devices.

3.Verify that Category 5 cable is used if you are operating at 100 Mbps, and that the length of any cable does not exceed 100 m (328 ft).

4.Check the network card connections.

5.The 10BASE-T/100BASE-TX port, network card, or cable may be defective.

81

Image 83

Contents Page Page Table of Contents Table of Contents Important Information Why should you do that?About the Wireless Barricade g Router LED IndicatorsFeatures and Benefits Features and BenefitsPackage Contents Installing the Wireless Barricade G RouterHardware Description Installing the Wireless Barricade g RouterFront and Rear Panels Hardware DescriptionConnect the System System RequirementsConnect the System Basic Installation ProcedureMaking the LAN Connections Attach to Your Network Using Ethernet CablingAttach to Your Network Using Radio Signals Making the WAN Connection Connecting the Power Adapter Windows 95/98/Me Installing TCP/IPWindows Configuring Client TCP/IPInstalling TCP/IP Configuring Your Computer in Windows 95/98/Me Setting Up TCP/IPSetting Up TCP/IP Obtain IP Settings from Your Wireless Barricade g Router Configuring Your Computer in Windows NT Configuring Client TCP/IP Configuring Your Computer in Windows Configuring Your Computer in Windows XP Configuring a Macintosh Computer Manual IP Configuration for all Windows OS Setting Up TCP/IP Verifying Your TCP/IP Connection Browser Configuration Configuring the Wireless Barricade G RouterInternet Explorer For Macintosh Configuring the Wireless Barricade g RouterDisable Proxy Connection Internet Explorer 5 or above For WindowsNavigating the Web Browser Interface Navigating the Web Browser InterfaceMaking Configuration Changes Time Zone Setup WizardSetup Wizard Broadband Type Fixed-IP xDSL Cable ModemPPPoE xDSL Point-to-Point Tunneling Protocol Pptp BigPond Advanced SetupDdns Advanced SetupTime Zone SystemPassword Settings Remote Management ZoneAlarm Pro with Web Filtering Setup Configuring the Wireless Barricade g Router Advanced Setup Configuring the Wireless Barricade g Router Syslog Server Dynamic IP WANPoint-to-Point Over Ethernet PPPoE Point-to-Point Tunneling Protocol Pptp Static IP Address BigPond DNS LAN Channel and Ssid WirelessConfiguring the Wireless Barricade g Router Security WPA Encryption Type WEP Encryption Type Configuring the Wireless Barricade g Router Address Mapping NAT Network Address TranslationVirtual Server Special Applications Trigger Public Port Public Type Comment Firewall Access ControlMAC Filtering Table URL Blocking Schedule Rule Advanced Setup Mail Alert Configuration Discard Ping from WAN Default EnableDMZ Demilitarized Zone Ddns Dynamic DNS Settings Ddns Service Provider Web Site UPnP Universal Plug and Play Setting Tools Tools Configuration ToolsTools Firmware Upgrade Tools Reset Section Description StatusVerify your connection to the Wireless Barricade TroubleshootingHave another IP Address displayed TroubleshootingAm getting an IP Address that starts with 10/100 LED does not light after a connection is made LAN Interfaces Advanced FeaturesStandards WAN InterfaceSpecifications Compliances SafetyFCC Radiation Exposure Statement Federal Communication Commission Interference StatementEC Conformance Declaration Class B CompliancesUnderwriters Laboratories Compliance Statement Safety ComplianceIndustry Canada Class B Australia AS/NZS 3548 1995 Class BWichtige Sicherheitshinweise Germany Legal Information Contacts SMCs Limited Warranty StatementLegal Information and Contacts Full Installation Manual Firmware and Drivers Contact SMCTrademarks Statement of Conditions Limitation of LiabilityCopyright Model Number SMC2804WBR