Seagate ST136403LW/LC manual LW model installation, Set the Scsi ID on the drive

Page 19

Cheetah 36 Installation Guide, Rev. A

17

How to install the drive

This installation guide provides step-by-step instructions to make your drive installation as easy as possible. Follow the installation steps listed for your drive model as listed below:

LW models (use the installation steps beginning below).

LC models (use the installation steps beginning on page 30).

LW model installation

1.Set the SCSI ID on the drive.

Determine which SCSI IDs are already being used in the system and then assign this disc drive a SCSI ID that isn’t already being used. Use the J6 connector located on the front of the drive to set the SCSI ID (see Figure 3).

• This drive is SCAM (SCSI Configured AutoMati-

cally) compliant. If you are installing this drive in a SCAM compliant system, you can skip this step because the system automatically assigns the drive SCSI

ID.

•The host system’s SCSI controller usually uses SCSI ID 7 so this SCSI ID is not usually available for disc drives or other devices.

•Most ST136403LW drives are factory set with the SCSI ID set at 0. If this is the only SCSI drive in your system and there are no other SCSI devices on the daisychain, you can leave this drive’s SCSI ID set to 0 and proceed to the next step. A device is any hardware other than an inline termina- tor that is connected to the SCSI cable.

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Cheetah Disc Drive ST136403LW/LC Contents Preface Electrostatic discharge protection Handling precautionsImportant safety information and precautions Cheetah 36 Installation Guide, Rev. a Wichtige Sicherheitshinweise Cheetah 36 Installation Guide, Rev. a Cheetah 36 Installation Guide, Rev. a Electromagnetic susceptibility Regulatory agency complianceElectromagnetic compliance Australian C-Tick Electromagnetic compliance for the European UnionGeneral description Primary benefits of LVD technology Single-ended and low voltage differential modesData bus widths SE and LVD bus configurationsProviding adequate cooling Kühlung des Systems Suggested air flow Characteristics ST136403LW/LC DC power requirements ±5%1 +5 +12 Set the Scsi ID on the drive LW model installationSetting the Scsi ID on LW model drives Configure termination Scsi bus termination Setting terminator power jumpers Configure termination powerConnect the drive activity remote LED optional Drive Active LED indicator connectionsWrite Protect option Delay Motor Start and Motor Start optionsParity Check option Additional jumper options Format the drive Mount the drive in the host system and connect cablingConnecting cables to the drive Multiple-drive connection to host adapter Mounting configuration dimensions LW model Alternate Scsi ID select and LED connection Additional connector on LW model drivesLC model installation Setting the Scsi ID on LC model drives Configure termination Delay Motor Start and Motor Start options M W P E E E E P D S S S Pin I/O connection to drive LC model Mount the drive in the host systemMounting configuration dimensions LC model Important information about formatting the drive System preparation DOS, Windows 3.1, Windows 95, and WindowsDrive formatting Macintosh Seagate Technology support services Presales Support Customer Service CSO European Support Services Africa/Middle East Support Services SeaFAX Page Page

ST136403LW/LC specifications

The Seagate ST136403LW/LC is a vintage hard disk drive that belongs to Seagate's esteemed lineup of storage solutions. Known for its reliability and performance during the era of its release, this model caters to various computing needs, particularly in enterprise and industrial settings.

One of the standout features of the ST136403LW/LC is its capacity of 36.4 GB, which, although modest by modern standards, was quite impressive in the early 1990s. This size made it ideal for businesses at the time looking to store substantial amounts of data without the high costs associated with larger enterprise solutions.

The drive operates at a speed of 7200 RPM, allowing for efficient data access and transfer. The spindle speed is crucial for performance, and 7200 RPM was considered rapid for hard drives in that period. This enhanced speed translates to quicker read and write times, making it suitable for applications that require timely data retrieval.

The ST136403LW/LC utilizes the SCSI interface, a popular choice in server environments for its robustness and speed. SCSI technology facilitates the connection of multiple drives, providing the ability to network various devices and manage them effectively. The multi-device capability is particularly beneficial for enterprise applications, ensuring that data centers can efficiently manage resources.

In terms of physical characteristics, the ST136403LW/LC is a 3.5-inch form factor drive, a standard size that fits into most desktops and servers of its generation. This compatibility is vital for users looking to upgrade their existing systems without the need for significant modifications.

The drive also includes built-in error correction features, enhancing data integrity and reliability, crucial for business operations where data loss can lead to substantial repercussions. Additionally, it employs a sealed enclosure design, providing protection against dust and moisture, thereby extending the drive's lifespan in demanding environments.

Furthermore, Seagate's reputation for durability is echoed in the ST136403LW/LC, as it was designed to endure the rigors of everyday use, particularly in enterprise settings where uptime is critical.

In conclusion, the Seagate ST136403LW/LC serves as an essential piece of technology from its era, characterized by its 36.4 GB capacity, 7200 RPM speed, SCSI interface, and robust construction. While modern storage solutions have far surpassed its capabilities, this drive remains a testament to Seagate's legacy in the storage industry, reflecting the innovations of its time.
Top Page Image Contents