Seagate ST31000524NS, ST3500514NS, ST32000644NS, 100516232, ST32000647SS manual Agency certification

Page 28

3.14Agency certification

3.14.1Safety certification

These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency.

3.14.2Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec- tromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024.

Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products.

Korean RRL

If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission, Republic of Korea.

These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab.

Family name: Constellation ES

Certificate number: STX-Constell-ES (B)

Australian C-Tick (N176)

If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).

3.14.3FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.

Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception.

Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this

22

Constellation ES Serial ATA Product Manual, Rev. G

Image 28
Contents Constellation ES Serial ATA ST32000644NS ST31000524NS ST3500514NSRevision history Revision DateContents Constellation ES Serial ATA Product Manual, Rev. G List of Figures Page Seagate Technology support services Seagate Online Support and ServicesIntroduction About the Serial ATA interface Specification summary tables Drive specifications summary0A optional configuration through Smart Command Transport Default logical geometry LBA modeFormatted capacity Recording and interface technologyPhysical characteristics Seek timeStart/stop times Typical seek times ms Read WritePower specifications 2000GB Drive DC power requirements 1000GB Drive DC power requirements 500GB Drive DC power requirements Typical DC Maximum DC Maximum DCpeak 12.22 12.26Typical current profiles Conducted noise Voltage tolerancePower-management modes Active modeIdle mode Sleep modePowerChoice is invoked using one of two methods Extended Power Conditions PowerChoiceTMPower Condition Name Power Condition ID Description PowerChoice Supported Extended Power Condition Indentifiers Power Condition Name Manufacturer Default Timer ValuesEPC Subcommand Description Power Condition Identifiers Power Condition NameTemperature a. Operating Environmental limitsHumidity Relative humidity AltitudeShock Operating shockAcoustics VibrationOperating vibration Nonoperating vibrationTest for Prominent Discrete Tones PDTs Electromagnetic immunityRadio frequency environments Test Description Performance level Reference standardReliability Agency certification Environmental protection Corrosive environment Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions-top, side and end view Drive mountingSerial ATA Sata interface Hot-Plug compatibilitySerial ATA device plug connector pin definitions Serial ATA connector pin definitionsSignal Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex F5H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordWord Set Features command Set Features command valuesM.A.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Constellation ES Serial ATA Product Manual, Rev. G Index ITE Page Constellation ES Serial ATA Product Manual, Rev. G Page Disc Drive, Scotts Valley, California 95066-4544, USA
Related manuals
Manual 48 pages 36.81 Kb