Install the RF Switch | Wegener Communications Unity RF Switch

Page 3

B. INSTALL THE RF SWITCH

See Figure 1 (Page 5) and Figure 2 (Page 5) of this guide for views of the module and its installation.

1.Remove the block-out plate from the Module where the switch is to be installed. These screws and holes will be used to mount the RF Switch in a later step. Use the #1 Philips Screwdriver for this.

2.From the inside of the unit, install the RF Switch into position. The “F” Connectors should protrude through the rear panel

3.Install one (1) self-tapping screw through the RF Switch Printed Wiring Board (PWB) into the hole in the bottom of the chassis. Leave it loose at this time. Only one screw will be used in this step, and which hole is used will depend on the module slot. This self-tapping screw “cuts” its own threads in the standoff hole, and may require moderate effort to turn it.

4.Line up the two holes in the rear of the RF Switch Bracket with the holes mentioned in Step # B1. Insert the self-tapping screws retained in Step # B1 through the receiver rear panel into the RF Switch Bracket. Tighten these screws snugly, but do not overtighten.

5.Tighten the Screw inserted in Step # B3 at this time. Do not overtighten.

6.Connect the supplied 10-pin cable from J1 on the RF Switch PWB to the appropriate connector on the receiver motherboard. If there is a cable from the RF Switch Expansion Bus to another board (either the Tuner Board or a Relay Board), note its location and remove that cable. Connect the middle connector of the new cable to the same connector on the previously installed Board.

7.On most units, the motherboard connector will be labeled “RF Switch Expansion Bus” or “Relay Expansion Bus,” and should have a number beside it corresponding to the number in the following table. See Table 1, below, for the various models. Make sure Pin 1 (the Red Line) on each cable connector goes to Pin 1 on each board connector. If you have any questions about this, contact system network control or Wegener Customer Service at 770-814-4057. Additional numbers are shown on the rear cover of this installation guide.

Table 1. Receiver Models and RF Switch Expansion Bus Connector Numbers

Receiver Model	Connector Number


UNITY401R	J7

UNITY500	J11

UNITY4000	J11

UNITY4422	J16

UNITY5000	J49

Page 3 of 6

800016-13

Unity RF Switch specifications

Wegener Communications has established itself as a leader in advanced telecommunications technology, and one of its standout products is the Unity RF Switch. This innovative device is designed to streamline and enhance the management of radio frequency signals in various applications, including broadcasting, telecommunications, and satellite communications.

The Unity RF Switch boasts several key features that set it apart in the marketplace. One of its primary functions is its ability to switch RF signals with high precision and reliability. This is crucial in environments where signal integrity is paramount, such as in live broadcasting scenarios or critical communication infrastructures. The switch is engineered to minimize signal loss, ensuring that the integrity of the transmitted data remains intact.

Another significant characteristic of the Unity RF Switch is its versatility. It is designed to accommodate a wide range of frequencies, making it adaptable to various applications. Whether handling VHF, UHF, or microwave signals, the Unity RF Switch is capable of meeting the diverse needs of today's broadcasting and telecommunications industries.

The Unity RF Switch also features advanced remote control capabilities. With the use of intuitive management software, operators can easily configure and control the switch from a distance. This remote functionality is particularly beneficial in large-scale operations or situations where equipment is located in hard-to-reach places. The software interface is user-friendly, allowing for quick adjustments and monitoring of system performance.

In terms of build quality, the Unity RF Switch is constructed with robust materials that ensure durability and reliability. It is designed to withstand various environmental conditions, making it suitable for deployment in both indoor and outdoor settings. The switch is also engineered for ease of installation, with clear documentation and support provided by Wegener Communications' expert team.

Another notable technological advancement in the Unity RF Switch is its support for automation and integration with existing broadcast systems. It can be seamlessly incorporated into complex workflows, enhancing operational efficiency. Additionally, the device supports multiplexing and demultiplexing, allowing for efficient management of multiple signals simultaneously.

In summary, the Wegener Communications Unity RF Switch is a sophisticated solution that addresses the challenges of RF signal management in modern telecommunications and broadcasting. Its high-precision switching capabilities, versatility, remote control features, and robust design make it an essential tool for professionals in the industry, ensuring seamless and reliable operation in critical applications.