Tyan Computer B2891 manual Features

Page 11

1.3Features

Enclosure

Industry 19” rack-mountable 1U chassis storage bay

(4) 3.5” HDD bays

(1) slim line CD-ROM bay

(1) slim line FDD bay

Dimension: D 25.4 x W 17.2 x H 1.72 inch (645x436x43.6mm)

Processors

Supports one or two AMD Opter- onTM 200 series processors

Chipset

nVIDIA nForce4 Professional + AMD-8131 Hyper Transport PCI-X Tunnel

Winbond W83627HF Super I/O chip

ADT7463 Hardware monitor IC

Memory

Eight 184-pin 2.5-Volt DDR DIMM sockets

Supports up to 16GB of Registered, ECC DDR400/333 memory

Supports Chipkill technology

Expansion Slots

One 64-bit 100MHz (3.3V) PCI-X slot, supporting low profile card (for S4H, S4-LC sku only)

One PCI-E x16 slot

Tyan TARO SO-DIMM connector for add-on storage controller card

Back I/O Ports

One keyboard & one PS/2 mouse ports

Two RJ45 10/100/1000 Base-T port with activity LED

Two USB 2.0 ports

One 9-pin UART serial port

One 15-pin VGA port

Front Panel Features

I/O

(2) USB 2.0 ports

LED indicators

Power LED

(2) LAN LEDs

HDD active LED

Switches

Power switch

Reset switch

Storage Controller

• Model B2891G24U4H:

Add-on Tyan M7901 SCSI con- .troller card (Adaptec AIC7901 single channel Ultra320 SCSI controller), connected to Tyan

TARO SO-DIMM

Supporting HostRAID 0,1 & 10

Model B2891G24S4H/S4-LC

Two dual-port SATAII controllers integrated in nVIDIA nForce4 Pro chip

Supporting 3Gb/s per port

Supporting RAID 0, 1, 0+1 and nVIDIA Morphing RAID (allowing to change the RAID type on the fly)

Storage

Model B2891G24U4H: SCSI ver- sion, supports up to 4 hot-swappa- ble Ultra320/160/ SCSI HDDs

Model B2891G24S4H: SATA ver- sion, supports up to 4 hot-swappa- ble SATA HDDs

Model B2891G24S4-LC: SATA ver- sion, supports up to 4 internal SATA HDDs.

Optional slim line CD-ROM, DVD- ROM and FDD

Networking

(2) Gigabit Ethernet ports (Broad- com BCM5704 dual port controller) connected to 133MHz PCI-X bus

Video

ATI RAGE XL PCI graphics control- ler

8MB Frame Buffer of video memory

Motherboard

Tyan Thunder K8SRE S2891G2NR

E-ATX footprint (13” x 12”)

Chapter 1: Overview

3

Image 11
Contents Transport GT24 B2891 Service Engineer’s Manual Page Preface Federal Communications Commission FCC Conventions Safety Information Table of Contents Technical Support About the Transport GT24 B2891 OverviewSupport Backplane Product ModelsB2891G24S4H B2891G24U4H B2891G24S4-LC Model HDD Bays Hot-SwapFeatures Server Management Regulatory Environment TemperaturePower Supply FDD Kit UnpackingRail Kit System Rear View About the ProductSystem Front View Rear I/O LED LED Definition Front PanelNo AC power System Internal View B2891G24S4H B2891G24S4-LC B2891G24U4H CPU1CPU0 Motherboard LayoutJumpers & Connectors Function Motherboard Block Diagram Memo Tools Before You BeginWork Area Precautions Rack mounting kit Installing the Server in a RackRack Mounting Screw the sliding brackets to the sliding rails Mounting Bracket Setting Up Removing the Chassis Cover Installing Motherboard ComponentsInstalling the CPU, Heatsink and Air Duct Setting Up Setting Up Installing the Memory Installing a PCI Card Setting Up Installing the Hard Drive for B2891G24S4H/U4H Setting Up Installing the Hard Drive for B2891G24S4-LC Setting Up Installing the Slim FDD Option Connect the other side to the connector on motherboard Memo Introduction Replacing Pre-Installed ComponentsPrecautions Following flowchart outlines the disassembly procedure Disassembly FlowchartRemoving the Cover Replacing Motherboard Components Disconnecting All Motherboard CablesMain Power EPS 12V Power Disconnect all fan power cables Removing the Motherboard Replacing the Slim CD-ROM Power Cable Data CableReplacing Pre-Installed Components Replacing the LED Control Board Replacing Pre-Installed Components Replacing the M1010 Adapter Board 1 M1010 Adapter Board Features System Fan Layout System Fan Monitoring Signal System Fan Speed Control Signal3 M1010 Adapter Board Connector Pin Definition FAN Signal Related Connector Pin Definition FAN112VPWM FAN1TACH GND FAN2TACH FAN212VPWM FAN512VPWM FAN5TACH GND FAN6TACH FAN612VPWM LCM+5V Lcmsin KEY PIN GND LCM+5VSB Lcmsout Replacing the Sata or Scsi Backplane Replacing Pre-Installed Components ATA Backplane M1204 Features Replacing Pre-Installed Components M1204 HDD Access LED Connector Pin Definition Scsi Backplane M1205 Features Replacing Pre-Installed Components Tion M1205 HDD Start-Mode & ID Selection SwitchCase Motor Spin FuncLeft to right in front view ID SequenceReplacing the Power Supply Boot Menu S2891 Mainboard BIOS/Advanced MenuTable of Differences B2891 S2891 B2891 Barebone Bios / Advanced MenuAppendix II Cable Connection Tables Power Supply Cable Other Cable Help Resources Technical SupportReturning Merchandise for Service