Omega A2400 manual Revised 4/17/95, Omega Engineering ONE Omega Drive, Box, FAX Mail das@omega.com

Page 3

A2400 USERS MANUAL

REVISED: 4/17/95

OMEGA ENGINEERING

ONE OMEGA DRIVE

P. O. BOX 4047

STAMFORD, CT 06907

PHONE: 1-800-DAS-IEEE

FAX: 203-359-7990

e-mail: das@omega.com

www.omega.com

The information in this publication has been carefully checked and is believed to be accurate; however, no responsibility is assumed for possible inaccuracies or omissions. Applications information in this manual is intended as suggestions for possible use of the products and not as explicit performance in a specific application. Specifica- tions may be subject to change without notice.

The A2400 series are not intrinsically safe devices and should not be used in an explosive environment unless enclosed in approved explosion-proof housings

Image 3
Contents User’sGuide Servicing North America For immediate technical or application assistanceServicing Europe STAMFORD, CT Phone 1-800-DAS-IEEE Revised 4/17/95Omega Engineering ONE Omega Drive BOXTable of Contents Introduction Chapter Getting StartedLeased Lines System Overview+99999.99 $1RDDefault Mode Page Chapter Functional Description Block DiagramFunctional Description Pinout RS-485 Termination A2400 OperationCharacter Filter Page Programmable Delay Times Page Chapter Communications Command $1RD Response *+99999.99DO, OC, CC, RD, REA, RID, RLP, RS, RSP, RSU Communication DATA+ RS-485 Multidrop SystemPage Command Structure Chapter A2400 Command SetResponse Structure Data StructureWrite Protection Miscellaneous Protocol NotesLong Form Responses Command Checksum?1 Syntax Error ?1 BAD Checksum$1WEF A2400 User Commands RT3 A2400 Command SetClosed Channel CC Extended Command DescriptionsCommand 01CC Response Response *01CC11 Digital Output do Command $1DO01 Response Command #1DO01 Response *1DO014FExtended Address EA Command $1DO00 Response Command #1DO00 Response *1DO004E$1ID Tank Farm #1ID Tank Farm1ID Tank Farm 1CD Command 01OC Response Response *01OCED Open Channel OC ExtendedRead Data RD 1RID Tank Farm 11F $1RIDTank Farm #1RID#1RSP $1RSU#1RSU $1RSPRead Time Delay 1 RT1 Response *1RT1+00100.00DC Read Time Delay 2 RT2Response *+00100.00 Page Page Short Prompt SP BAD Checksum Command 01WE Response *01WE27Error Messages Address ErrorValue Error Command ErrorParity Error Syntax ErrorChapter Setup Information/SetUp Command Command Syntax$1SUbyte 1byte 2byte 3byte Byte HEX Ascii Byte 1 Ascii Printable CharactersBaud Rate ParityCommand $1RS Response *31070000 Command $1WE Response Command $1SU31020000Command $1RS Response *31020102 Command $1WE Baud Command $1RR ResponseBit Byte 2 Linefeed, Parity and Baud RateNormal addressing Chapter Delay Time Programming Delay Time Programming Page Command $1RT1 Response *+00100.00 Command $1T3+00050.00 Set T3 to 50 ms ResponseChapter Power Supply Chapter Troubleshooting Symptom RS-232 Module is not responding to commandsSymptom RS-485 Module is not responding to commands Command 01WE Response Open/Close Channel CommandsChapter Extended Addressing Typical system overview Command 02OC Response Command 01OC ResponseCommand $1RD Response +00100.00 Typical $2RD +00123.45 Command 01CC ResponseExtended Address Syntax Structured AddressingCommand Response OC and CC Command FormatsImplied CC Command Implied OC CommandCommand Response *01OC1D Single Command Module Address Command 01$1RD Response *+00100.00Explicit Open and Close Channel Commands Command 02OC Response 02OC1E ‘1E’ is the checksum Command 01CC Response 01CC11 ‘11’ is the checksumTransparent Mode Functions Chapter Transparent ModeA2400 interfacing a PLC to a leased-line modem A2400 networking several RS-232 devices to a host computer A2400 interfacing a laboratory instrument with modules Transparent Mode Adding secondary control using A2400 modules Transparent Mode WARRANTY/DISCLAIMER Shop online at omega.com