Clarion XMD1, XMD2 owner manual Operation

7. OPERATION

Note:

• Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3.

Basic Operations

CAUTION

When this unit is turned on, starting and stopping the engine of a boat with its volume raised to the maximum level may harm your hearing.

Be careful about adjusting the volume.

IMPORTANT

Door must be totally closed to prevent water go into the set!

OK NG

Adjusting the Balance

1)Press A-M button # and select “BAL”.

2)Press the volume wemphasizes the sound from the right speaker; press the volume z emphasizes the sound from the left speaker.

∗ The factory default setting is “0”. (Adjustment range: L9 to R9)

3)When the adjustment is complete, press A-M button # several times until the function mode is reached.

Adjusting the Fader

1)Press A-M button # and select “FAD”.

2)Press the volume w emphasizes the sound from the front speak- ers; press the volume z emphasizes the sound from the rear

speakers.

∗ The factory default setting is “0”. (Adjustment range: F9 to R9)

3)When the adjustment is complete, press A-M button # several times until the function mode is reached.

Setting the Z-enhancer

This unit comes with three types of sound tone effects stored in memory. Select the one you prefer.

∗The factory default setting is “Z-EHCR OFF”.

Turning ON the Power and Adjusting the Volume

1)Press the POWER button 4.

∗ To turn off the power, press the POWER button 4for 1 second or longer.

2)Press the FUNC button 4 and select another operation mode. Every time the FUNC button 4 is pressed, the display changes the operation mode as:

Radio ➜ CD ➜ CD changer ➜ Radio

Notes:

•The operation mode not connected to the unit will not be selected.

•If the CD mode is selected when no disc is inserted, the display

flashes “DISC”.

3)Use the volume button 1 to adjust the volume. w: Increases the volume.

z: Decreases the volume.

∗ The volume level is from 0 (minimum) to 33 (maximum).

Each time you press Z-EHCR button &, the tone effect changes in the following order.

“Z-ENHANCER 1”➜ “Z-ENHANCER 2”➜ “Z-ENHANCER 3”➜ “Z- EHCR OFF” ➜ “Z-ENHANCER 1”...

•Z-ENHANCER 1: bass emphasized

•Z-ENHANCER 2: treble emphasized

•Z-ENHANCER 3: bass and treble emphasized

•Z-EHCR OFF: no sound effect

Loudness Effect

In order to turn on/off the loudness effect, use the LOUD button # for 2 seconds or longer. Every time the LOUD button # is pressed and held for 2 seconds or longer, the loudness effect switches on and off.

∗When the loudness effect is on, the display will show “LD”.

Audio Mode Adjustments

Press the A-M button # to select the adjustment mode. The mode switches as follows each time the A-M button is pressed:

BASS ➜ TREB ➜ BAL ➜ FAD ➜ Previous mode

Adjusting the Bass

1)Press A-M button # and select “BASS”.

2)Press volume button 1 w to emphasizes the bass; press z to

attenuates the bass.

∗ The factory default setting is “0”. (Adjustment range: –6 to +6)

3)When the adjustment is complete, press A-M button # several times until the function mode is reached.

Adjusting the Treble

1)Press A-M button # and select “TREB”.

2)Press volume button 1 w to emphasizes the treble; press z to

attenuates the treble.

∗ The factory default setting is “0”. (Adjustment range: –6 to +6)

3)When the adjustment is complete, press A-M button # several times until the function mode is reached.

Switching the Clock Display

Every time the DISP button % is pressed, the display will change between the operation mode and the clock display.

Setting the Clock

1)Press the DISP button % to display the clock display.

2)Press and hold the DISP button % for 2 seconds or longer.

3)Press the SRCH Left button @, then set the current hour.

4)Press the SRCH Right button @, then set the current minute.

5)Press the DISP button %, then the clock is set.

Notes:

•If you select another operation mode while you are setting the clock, the clock setting operation will be canceled.

•If you remove the vehicle’s battery for a check or repair, the clock will be reset, so you must set it again.

6 XMD1/XMD2