Omega Vehicle Security DPC10-CS Count Scaler, Calculating the Count Scale Factor, Display DPF

Page 3

COUNT SCALER

Calculating the Count Scale Factor

The count scale factor is used to convert the incoming count pulses to the desired unit of measure to be displayed (feet, gallons, etc.) or to correct for a known amount of error (wheel wear, viscosity, etc.). This scaler has six digits available with a fixed decimal point.

Count Scaler Range: 0.0001 to 99.9999

(Setting the count scale factor to 0.0000 will allow scaling by 100)

Count Scaler (CS) Formula:

cs=E$

where:

DPF is the decimal point factor corresponding to the desired decimal point location.

DISPLAY

DPF

DISPLAY

DPF

xxxxxx = 1

 

xxx.xxx = 1,000

xxxxx.x = 10

 

xx.xxxx = 10,000

xxxx.xx = 100

PPI is the number of pulses per item from the sensor.

Example 1: A sensor produces20 pulses per inch of material travel. Calculate the count scaler required to indicate mate- rial used in whole inches(XXXXXX).

cs= 1 = 0.05000 20

Example 2: An encoder produces 120 pulses per foot. Calculate the count scaler required to indicate material usage in 1/100 ’s of feet (XxXx.Xx).

cs = = = 0.8333 120

(Select the XXXX.XX position on the totalizer decimal point menu).

Programming Count Scale Factor

The first screen in the program mode is used to enter the count scale factor.

;

The far right digit will be flashing. Press the m key until reaching the desired digit value.

Note: Pressing and holding the m key will cause the numbers to autoscroll.

Next press them key to move the flashing digit one place to the left. Change this digit to the desired value with the m key.

Repeat this process until all digits are set correctly.

Programming Decimal Point

The second screen is used to enter the decimal point display on the totalizer screen. Press and hold the m key and

then press them key to move from screen one to screen two.

Press them key to move the decimal point to the desired position.

Programming Offset Value

Programming an offset value allows the counter to reset to a value other than zero. The offset may be up to six digits. The offset cannot be a negative number.

The third screen in the program mode is used to enter the offset value.

The far right digit will be flashing. Press the m key until reaching the desired digit value.

Note: Pressing and holding the m key will cause the numbers to autoscroll.

Next press them key to move the flashing digit one place to the left. Change this digit to the desired value with the m key. Repeat this process until all digits are set correctly.

Page 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 7mm 95 74.93mm -H 677 68mm -wRear View Program ModeIntroduction Front ViewCount Scaler Calculating the Count Scale FactorDisplay DPF Operation Wiring RecommendationsWiring Diagrams BatterysafetyDPC Replacement PartsRequests / lNQUlRlES &$~~ Other Omega MPH/CONDUCTIVITY Temperature

DPC10-CS specifications

The Omega Vehicle Security DPC10-CS is an advanced car security system designed to provide comprehensive protection against theft and unauthorized access. This system is particularly suited for individuals who prioritize vehicle safety and features an array of state-of-the-art technologies to safeguard vehicles effectively.

One of the standout features of the DPC10-CS is its dual zone shock sensor. This technology detects any tampering or disturbances around the vehicle, triggering an alarm to deter potential thieves. The sensitivity of the shock sensor can be adjusted according to the user's preference, ensuring it adapts to varying environmental conditions.

Another notable characteristic of the DPC10-CS is its ability to control the vehicle’s central locking system. This feature allows for secure locking and unlocking, providing peace of mind when leaving the vehicle unattended. Additionally, the system includes an immobilizer function that prevents the engine from starting without the correct key, adding an extra layer of security against theft.

The DPC10-CS is equipped with a user-friendly remote control, allowing easy access to vehicle functions. This remote not only controls the locking mechanisms but also activates the alarm system from a distance, enabling users to monitor their vehicle's security status conveniently. The remote typically features LED indicators that provide visual feedback on the system's status.

Another innovative aspect of this security system is its programmable features. Users can tailor the settings to meet their specific security needs, including adjusting the alarm siren duration, sensitivity levels, and alarm triggers. This flexibility ensures that the security system performs optimally in various scenarios.

The installation of the Omega Vehicle Security DPC10-CS is straightforward, making it accessible for professional installers and vehicle enthusiasts alike. The system is designed to integrate seamlessly with most vehicles without causing any damage or voiding warranties.

In conclusion, the Omega Vehicle Security DPC10-CS combines cutting-edge technologies and user-friendly features to create a robust vehicle security solution. Its shock sensors, remote control capabilities, and programmable options make it an exceptional choice for those seeking to enhance their vehicle's security while maintaining convenience. With the DPC10-CS, vehicle owners can feel confident that their investment is well protected against potential threats.
Top Page Image Contents