NETGEAR GS724TPS-100NAS, GS700TP, 724TP manual Installing the Switch on a Flat Surface

Page 17

 

GS700TP Hardware Installation Guide

 

 

Table 2-1. Site Requirements (continued)

 

 

Characteristics

Requirements

 

 

Power source

Provide a power source within 6 feet (1.8 meters) of the installation location. Power

 

specifications for the switch are shown in Appendix A Appendix A “Troubleshooting”.

 

Ensure the AC outlet is not controlled by a wall switch, which can accidentally turn off

 

power to the outlet and the switch.

 

 

Environmental

• Temperature - Install the switch in a dry area, with ambient temperature between 0 and

 

40ºC (32 and 104ºF). Keep the switch away from heat sources such as direct sunlight,

 

warm air exhausts, hot-air vents, and heaters.

 

• Operating humidity - The installation location should have a maximum relative

 

humidity of 90%, non-condensing.

 

• Ventilation - Do not restrict airflow by covering or obstructing air inlets on the sides of

 

the switch. Keep at least 2 inches (5.08 centimeters) free on all sides for cooling. Be

 

sure there is adequate airflow in the room or wiring closet where the switch is installed.

 

• Operating conditions - Keep the switch at least 6 ft. (1.83 m) away from nearest

 

source of electromagnetic noise, such as a photocopy machine.

 

 

Step 2: Installing the Switch

The NETGEAR Smart Switch can be installed on a flat surface or in a standard 19-inch rack.

Installing the Switch on a Flat Surface

The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the four concave spaces on the bottom of the switch. The rubber footpads cushion the switch against shock/vibrations.

Installing the Switch in a Rack

To install the switch in a rack, use the following procedure (and refer to Figure 2-1). To perform this procedure, you need the 19-inch rack-mount kit supplied with switch.

1.Attach the supplied mounting brackets to the side of the switch.

2.Insert the screws provided in the rack-mount kit through each bracket and into the bracket mounting holes in the switch.

3.Tighten the screws with a #1 Phillips screwdriver to secure each bracket.

4.Align the mounting holes in the brackets with the holes in the rack, and insert two pan-head screws with nylon washers through each bracket and into the rack.

Installation

2-30

v1.0, September 2007

Page 16 Page 18
Image 17
Page 16 Page 18
Contents GS700TP 724TP, 748TP Series Hardware Installation Guide Technical Support Voluntary Control Council for Interference Vcci Statement Product and Publication Details Contents Appendix a Troubleshooting Conventions, Formats and Scope About This GuideHow to Print this Manual How to Use This ManualRevision History Overview Chapter IntroductionIntroduction Switch Features GS700TP Hardware Installation Guide Package Contents GS700TP Hardware Installation Guide Preparing the Site Chapter InstallationInstalling the Switch in a Rack Installing the SwitchInstalling the Switch on a Flat Surface Checking the Installation Installing an SFP Gbic Module Connecting Devices to the SwitchApplying AC Power GS700TP Hardware Installation Guide Chapter Physical Description Front and Back Panel ConfigurationGS724TP Front and Back Panels Configuration GS748TP Front and Back Panels Configuration Port LEDs LED DesignationsFollowing table describes the system LED designations System LEDsRJ-45 Ports Device Hardware InterfacesSFP Gbic Module Factory Defaults ButtonTroubleshooting Chart Appendix a TroubleshootingConfiguration Additional Troubleshooting SuggestionsSwitch Integrity Network Adapter CardsAuto-negotiation Appendix B Technical Specifications Physical Specifications Power SupplyEnvironmental Specifications SafetyModules Numerics IndexIndex-2 Index-3

GS700TP, 724TP, GS748TP-100NAS, GS724TPS-100NAS specifications

NETGEAR is a leading provider of networking solutions, and its range of smart switches exemplifies the brand's commitment to performance and innovation. Among these, the NETGEAR GS724TPS-100NAS, GS748TP-100NAS, and GS700TP series, along with the GS724TP model, stand out for their robust features and reliability for enterprises of all sizes.

The NETGEAR GS724TPS-100NAS is a 24-port gigabit PoE switch designed to deliver high performance and power for various devices. With 24 Power over Ethernet (PoE) ports, it supports a total power budget that accommodates IP cameras, wireless access points, and VoIP phones with ease. This model incorporates advanced Layer 2 features and VLAN support, allowing network segmentation for enhanced security and traffic management.

The GS748TP-100NAS model takes it a step further by providing 48 PoE ports, creating an even more extensive network environment suitable for larger organizations. It offers advanced management capabilities with a user-friendly web interface and supports SNMP, RMON, and a variety of redundancy protocols to ensure network uptime. Its increased throughput performance ensures that data-intensive applications can run smoothly across the network.

The GS700TP series is designed for enterprises seeking advanced smart managed capabilities. These switches offer extensive configurations and additional features such as link aggregation and advanced quality of service (QoS). This permits prioritized bandwidth allocation for critical applications, ensuring optimal performance.

The GS724TP, similar to the GS724TPS, includes 24 ports but differs in that it provides a hybrid of managed and unmanaged features, making it versatile for businesses that do not require extensive management overhead. With a sturdy build and energy-efficient technologies, these switches significantly contribute to reduced operational costs.

All models feature NETGEAR's innovative Smart Control Center software, allowing easy centralized management. The energy-efficient design aligns with environmental standards, making the GS series eco-friendly options for contemporary networks. These switches are equipped to handle IP traffic with advanced monitoring tools, making them ideal for businesses that require reliable and scalable networking solutions.

In summary, NETGEAR's GS series enhances network reliability and management with a blend of robust features, making them an ideal choice for businesses looking to streamline their networking infrastructure while investing in future growth.
Top Page Image Contents