NETGEAR GS105 manual 3Install the Switch and Connect the Other Devices, GA302T Adapter

Page 5

3Install the Switch and Connect the Other Devices

Apple G4

PC with

GA302T

Adapter

 

10/100/1000 Mbps Gigabit Switch GS105

 

GigabitEthernet

1000M

100M

 

 

On=10M, Blink=ACT

 

 

 

 

 

Auto

 

 

 

 

 

 

 

 

 

 

Uplink

 

1

2

3

4

5

 

 

 

 

 

Power

Green=FDX, Yellow=COL

1

2

3

4

5

GS105 5-Port 10/100/1000 Mbps

Gigabit Ethernet Switch

Server with GA622T

DSL

Adapter

modem

 

 

 

 

LOCAL

 

 

 

 

 

 

 

 

 

10/100M

 

 

 

 

 

8

7

6

5

4

3

2

1

INTERNET

 

 

 

 

 

 

 

 

 

12VDC 1.2A

 

 

 

 

 

 

 

 

 

OFF

ON

FVS318 ProSafe VPN Firewall

1.Place the switch on a flat surface or hook onto the screws.

2.For each device, insert one end of an Ethernet cable into the port in the device and insert the other end into one of the Ethernet ports on the switch.

3.Connect the power adapter’s cord into the back of the switch and then plug the adapter into a power source (such as a wall socket or power strip).

The Power light

Power

ACT, FDX, COL LED

 

 

 

 

 

 

 

 

 

 

 

1000M

100M

should light up.

 

 

 

 

 

 

 

 

 

 

 

 

LED

 

LED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The corresponding

 

 

 

 

 

10/100/1000 Mbps Gigabit Switch GS105

 

 

 

 

Gigabit

Ethernet

 

 

 

1000M

 

 

100M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On=10M, Blink=ACT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Uplink

Link LED for each

 

 

 

 

1

2

3

4

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connected and

Power

 

Green=FDX, Yellow=COL

1

 

2

 

3

 

4

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Model GS105 5-Port 10/100/1000 Mbps Gigabit Ethernet Switch

powered device

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

should light and flash when activity occurs. If the connection is 1,000 Mbps or 100 Mbps, the LED in the RJ-45 jack will light up. If the connection is 10 Mbps, the 10M LED on the left side of the front panel will light up.

Note: If any light doesn’t operate as indicated, go to the Troubleshooting section.

Image 5
Contents Port Switch Introduction Installation OverviewUnpack the Box and Verify the Contents Prepare to Install the Switch GA302T Adapter 3Install the Switch and Connect the Other DevicesTechnical Specifications TroubleshootingEN 55 022 Declaration of Conformance Statement of ConditionsCertificate of the Manufacturer/Importer Support Information Technical Support
Related manuals
Manual 23 pages 35.1 Kb