NetComm N300 manual 3G Internet Settings, Apn, ‘Off’, Pin, Dns

Page 17

NetComm Liberty Series - 3G Wireless N300 Router

3G Internet Settings

3G Internet Settings

This page allows you to setup your WWAN (Wireless Wide Area Network) connection. Enter the relevant settings as provided by your 3G provider.

Note For 3G WAN connection: The 3G connection fields may not be necessary for your connection. The information on this page will only be used when your service provider requires you to enter a User Name and Password to connect to the 3G network.

Name

description

 

 

APN:

Enter the APN for your 3G USB modem

 

 

User Name:

Enter your 3G username

 

 

Password:

Enter your 3G password

 

 

Operation Mode; There are 3 options:

 

 

‘Always On’

Keeps the Internet connection alive, does not disconnect.

 

 

‘OFF’

Does not connect to the Internet.

 

 

‘Automatic 3G Backup’

The Automatic 3G Backup feature of the 3G18Wn is designed to provide a

 

backup 3G Internet connection in case your primary connection should fail.

 

To use this feature, you will need both an Ethernet WAN connection (from an

 

xDSL modem/ISDN/Satellite etc) and a 3G WAN connection.

 

 

PIN:

Enter the Pin Code for your SIM card

 

 

Note: For current APN’s of various providers, consult the Setting Up Your Router section of this user manual

WAN

Select the WAN connection type suitable for your environment and configure parameters according to the selected connection type.

STATIC (fixed IP)

If your WAN connection uses a static IP address, please select Static IP Address and fill in the required information in the fields provided.

Name

description

 

 

IP Address:

Type in the IP address assigned by your Internet Service Provider

 

 

Subnet Mask:

Type in the Subnet mask assigned by your Internet Service Provider

 

 

Default Gateway:

Type in the WAN Gateway assigned by your Internet Service Provider

 

 

Primary/ Secondary

Type in the DNS address assigned by your Internet Service Provider

DNS:

 

 

 

MAC Clone:

Please input the MAC address of your computer here if your service provider only permits

 

computers with a certain MAC address to access the Internet. If you are using the

 

computer which used to connect to the Internet via a cable modem, you can simply press

 

the ‘Default’ button to fill the MAC address field with the MAC address of your computer.

 

 

Click Apply to save the settings.

YML18WN

3G18Wn User Guide

www.netcomm.com.au

17

Image 17
Contents 3G Wireless N300 Router Save Our Environment Important Safety InstructionsPreface Table of Contents Introduction Package Contents Your 3G18Wn 3G Wireless N300 RouterKey Features IntroductionPlacement Avoid obstacles and interference Placement of your 3G18WnRouter Placement Cordless Phones Choose the Quietest Channel for your Wireless NetworkProduct Layout Wireless Computer System Requirements Connecting and Configuring your RouterProduct Layout Network and System RequirementsPlug in the power Connecting your 3G RouterModem Requirements Connect the USB 3G ModemConfiguring your Router and setting up your computer Default SettingsFor 3G connections Setting up your 3G RouterMac OSX For Non-3G Connections 3G Internet Settings3G Connection Status Advanced Features Status Advanced FeaturesLogin Procedure APN 3G Internet Settings‘OFF’ PINAddress field with the MAC address of your computer Pptp LAN Dhcp Client Advanced RoutingAdvanced Routing Static Advanced Routing DynamicWireless Settings Basic Wireless SettingsAdvanced WEP Security ModeSecurity PSK WPA/WPA2WPA-PSK/WPA2 WPS Station ListWPS Ssid WPS PINFirewall MAC/IP/Port Filtering FirewallDMZ Port ForwardingSystem Security Content FilteringAdministration Management AdministrationUpload Firmware DdnsSystem Log Setting ManagerStatistics Troubleshooting Why my wireless client can not access the Internet? TroubleshootingWhy does my wireless connection keep dropping? Cannot establish a wireless connection?What can I do if my Ethernet cable does not work properly? How do I reset my 3G18Wn to its factory default settings?Do not remember my encryption key. What should I do? Establishing Your Wireless Connection Windows XP service pack Establishing Your Wireless ConnectionMac OSX NetComm Liberty Series 3G Wireless N300 Router Windows Vista How To configure Wireless Security How To Configure Wireless Security Appendix GNU General Public License Product WarrantyCustomer Information Limitations of Warranty Product Warranty Technical Support