Minicom Advanced Systems 116 IP manual Taking over a busy remote session, Toolbar

Page 34

SMARTRACK 116 IP

On the remote console you have the following:

Server Confirmation label – This confirms the identity of the current server accessed and disappears by default after 30 seconds, (this period can be adjusted in the OSD – explained in Section II of the guide). It appears again when switching to a different server. The currently accessed server identity can be checked any time by looking at the Server name on the Internet Explorer title bar.

Toolbar icon – This is the minimized toolbar from which you switch and configure the system.

Minicom icon – Hold the mouse over the icon to view information about current server, connection time and video mode.

21.1 Taking over a busy remote session

While only one user can have control, many users can be connected simultaneously. When connecting to a busy Target Server an Administrator has the option to take over the Target Server. A User only has this option when the current session is run by another User, but not by an Administrator. The following message appears

Figure 36 Busy remote session options

Choose to Take Over or View Only or Cancel.

When watching a screen in View Only mode you can Double click inside the Remote screen border – see Figure 35 – to take over the remote control. The current user sees a message stating that control has been taken over.

21.2The Toolbar

To maximize the Toolbar:

Click the arrow . Click again to minimize the Toolbar.

When maximized, the Toolbar can be dragged and dropped to anywhere on the

screen, by dragging the icon . When minimized the icon glides to a side of the screen.

33

Image 34
Contents SmartRack 116 IP User Guide Table of Contents Troubleshooting Safe mode Updating the firmware Manually updating ROCs Technical precautions WelcomeSection Key featuresIntroduction Hardware kit contents System componentsPre-installation guidelines Connecting to a rack Avoiding general rack mounting problemsAdjust the rear bracket to fit your cabinet, see below Tightening the 7 screws Using the longer bracket for rack depth of 905 ~ 990mm Connecting three flat screws to the rear of the consoleConnecting the KVM Switch 116 IP Removing the six screwsConnecting the bracket a to the sides of the Switch SmartRack Switch system configuration 116 switchConnector table Connecting ROCs to serversConnecting a ROC PS/2 Connecting a ROC USB ROC PS/2 connectionsConnecting to the network Initial settings Default IP addressConnecting the CAT5 cables Connecting the power supplyStatic IP addresses for a number of units Boot-up process Logging into the Web interface SSL Certificate notesNetwork Configuration 11.1 LANNetwork Snmp Settings 11.2 KVM.netSnmp Events table Table below list all events recordedConfsecuritychanged Administration User Settings AdministratorDeleting a user Adding a userEditing a user Blocking a userAdministration Switch Configuration Administration User TargetsSecurity Settings User Targets ConfigurationSecurity SSL Certificate Standard security policy High security policyMaintenance Firmware Upgrade Restore Factory SettingsSaving changes and logging out Starting a remote sessionSelect Run as administrator Taking over a busy remote session ToolbarSwitching to a different server Changing the performance settingsManual Video Adjust Adjusting the Video settingsRefresh Auto Video Adjust Manual Video Adjustments controlsPower cycle Keyboard key sequencesSynchronizing mouse pointers Click Stop RecordingCalibrating mice pointers Aligning the mice pointersManual mice synchronization Examples Minicom icon menu features Mouse Emulation Dialog boxFull screen mode Troubleshooting Safe modeDisconnecting the remote session Entering Safe mode Safe mode procedureRestoring factory defaults Safe mode menuReboot Restoring the device firmwareOSD Switching between computersKeyboard hotkeys Navigating the OSD OSD settings F2Selecting a computer General settings General Settings windowUser Status U 24.1.5 F7 Defaults Ports settingsTime settings Time settings windowUsers settings window UsersSecurity OSD Help window F1Tuning F5 Scanning computers- F4Moving the label F6 DDC F10Connecting the RS232 Download cable Connecting the SmartRack 116 IP systemInstalling the software Upgrading the SmartRack 116 IP firmwareStarting and configuring the SmartRack 116 IP Update Smartrack 116IP SwitchVerifying the version numbers Button or Box FunctionObtaining new firmware Updating the firmware Troubleshooting the Update software Manually updating ROCsCommunication Error message Resetting through the Update softwareSetting default values for the OSD Getting the current statusUser Guide Technical specifications Flash RJ11ROCs User guide feedback Video resolution and refresh ratesSafety Weee complianceRegional Offices
Related manuals
Manual 56 pages 54.57 Kb

116 IP specifications

Minicom Advanced Systems has made significant strides in the realm of data center infrastructure solutions, particularly with the introduction of the Minicom Advanced Systems 116 IP. This device is designed primarily for providing advanced control and management for IT professionals seeking robust and efficient ways to manage access to their server rooms and IT environments.

One of the standout features of the Minicom Advanced Systems 116 IP is its support for IP-based KVM (Keyboard, Video, Mouse) switching. This technology allows users to remotely access and control multiple servers from a single workstation, eliminating the need for physical access to each machine. This is particularly beneficial in large data center environments, where time and space efficiency are critical.

The 116 IP model offers a high-resolution video output, supporting resolutions up to 1920x1200. This ensures that users can maintain the clarity of visual data while managing their systems remotely. The system is compatible with a myriad of operating systems, including Windows, Linux, and Mac, which makes it versatile for various IT environments.

Security is a paramount consideration for any organization dealing with sensitive data. The Minicom 116 IP incorporates advanced security features, including user authentication protocols and encryption mechanisms. This ensures that only authorized personnel can access the systems, reducing the likelihood of data breaches and unauthorized access.

Moreover, the device is equipped with hot-plugging capabilities, allowing users to add or remove servers without needing to power down the system. This feature enhances uptime and productivity, as administrators can make changes without disrupting ongoing operations.

In addition to its technical facets, the Minicom 116 IP is designed with user experience in mind. It features a user-friendly interface that simplifies the management of multiple servers, making it easier for IT staff to navigate between different machines.

Finally, the device is built for scalability, allowing organizations to expand their IT infrastructure as they grow. This flexibility means that the Minicom Advanced Systems 116 IP can adapt to increasing demands without necessitating a complete overhaul of existing systems.

In summary, the Minicom Advanced Systems 116 IP presents a suite of advanced features, including high-resolution output, robust security protocols, hot-plugging capabilities, an intuitive user interface, and scalable architecture, making it an ideal solution for modern data center management needs.