Minicom Advanced Systems 116 IP manual Aligning the mice pointers, Calibrating mice pointers

Page 40

SMARTRACK 116 IP

21.8.1 Aligning the mice pointers

When accessing the Target Server, the mice may appear at a distance to each other. To align the mouse pointers:

From the Toolbar click / Align or press Ctrl+M simultaneously. The mice align.

21.8.2 Calibrating mice pointers

A Target Server may have a different mouse pointer speed to the Client computer. Calibrating automatically discovers the mouse speed of the Target Server and aligns the two pointers.

To perform the calibration when the Target Server Operating system is, Windows NT4, 2000 or 98:

From the Toolbar click / Calibrate. SmartRack 116 IP saves this alignment so calibration is only needed once per Target Server.

If the Video Noise Level is above zero, calibration may not work. Go to Video Adjustment and try to eliminate the noise by pressing Auto video adjust and/or adjusting the bars in Manual video adjust, then perform the mouse calibration.

Note! If the mouse settings on the Target Server were ever changed, you must synchronize mouse pointers manually, as explained below.

21.8.3 Manual mice synchronization

If the mouse settings on the Target Server were ever changed, or when the Operating system on the Target Server is, Windows XP / 2003 Server / Vista/ 2008 Server, Linux, Novell, SCO UNIX or SUN Solaris you must synchronize the mouse pointers manually.

To manually synchronize mouse pointers:

1.From the Toolbar click / Manual Settings. The Mouse Settings Dialog box appears see Figure 41.

39

Page 39 Page 41
Image 40
Page 39 Page 41
Contents SmartRack 116 IP User Guide Table of Contents Troubleshooting Safe mode Updating the firmware Manually updating ROCs Technical precautions WelcomeSection Key featuresIntroduction Hardware kit contents System componentsPre-installation guidelines Connecting to a rack Avoiding general rack mounting problemsAdjust the rear bracket to fit your cabinet, see below Tightening the 7 screws Using the longer bracket for rack depth of 905 ~ 990mm Connecting three flat screws to the rear of the consoleConnecting the KVM Switch 116 IP Removing the six screwsConnecting the bracket a to the sides of the Switch SmartRack Switch system configuration 116 switchConnector table Connecting ROCs to serversConnecting a ROC PS/2 Connecting a ROC USB ROC PS/2 connectionsInitial settings Default IP address Connecting the CAT5 cablesConnecting to the network Connecting the power supplyStatic IP addresses for a number of units Boot-up process Logging into the Web interface SSL Certificate notesNetwork Configuration 11.1 LANNetwork Snmp Settings 11.2 KVM.netSnmp Events table Table below list all events recordedConfsecuritychanged Administration User Settings AdministratorAdding a user Editing a userDeleting a user Blocking a userAdministration Switch Configuration Administration User TargetsSecurity Settings User Targets ConfigurationSecurity SSL Certificate Standard security policy High security policyMaintenance Firmware Upgrade Restore Factory SettingsSaving changes and logging out Starting a remote sessionSelect Run as administrator Taking over a busy remote session ToolbarSwitching to a different server Changing the performance settingsManual Video Adjust Adjusting the Video settingsRefresh Auto Video Adjust Manual Video Adjustments controlsPower cycle Keyboard key sequencesSynchronizing mouse pointers Click Stop RecordingCalibrating mice pointers Aligning the mice pointersManual mice synchronization Examples Minicom icon menu features Mouse Emulation Dialog boxFull screen mode Troubleshooting Safe modeDisconnecting the remote session Entering Safe mode Safe mode procedureRestoring factory defaults Safe mode menuReboot Restoring the device firmwareOSD Switching between computersKeyboard hotkeys Navigating the OSD OSD settings F2Selecting a computer General settings General Settings windowUser Status U 24.1.5 F7 Defaults Ports settingsTime settings Time settings windowUsers settings window UsersSecurity OSD Help window F1Tuning F5 Scanning computers- F4Moving the label F6 DDC F10Connecting the SmartRack 116 IP system Installing the softwareConnecting the RS232 Download cable Upgrading the SmartRack 116 IP firmwareStarting and configuring the SmartRack 116 IP Update Smartrack 116IP SwitchVerifying the version numbers Button or Box FunctionObtaining new firmware Updating the firmware Troubleshooting the Update software Manually updating ROCsResetting through the Update software Setting default values for the OSDCommunication Error message Getting the current statusUser Guide Technical specifications Flash RJ11ROCs Video resolution and refresh rates SafetyUser guide feedback Weee complianceRegional Offices
Related manuals
Manual 56 pages 54.57 Kb

116 IP specifications

Minicom Advanced Systems has made significant strides in the realm of data center infrastructure solutions, particularly with the introduction of the Minicom Advanced Systems 116 IP. This device is designed primarily for providing advanced control and management for IT professionals seeking robust and efficient ways to manage access to their server rooms and IT environments.

One of the standout features of the Minicom Advanced Systems 116 IP is its support for IP-based KVM (Keyboard, Video, Mouse) switching. This technology allows users to remotely access and control multiple servers from a single workstation, eliminating the need for physical access to each machine. This is particularly beneficial in large data center environments, where time and space efficiency are critical.

The 116 IP model offers a high-resolution video output, supporting resolutions up to 1920x1200. This ensures that users can maintain the clarity of visual data while managing their systems remotely. The system is compatible with a myriad of operating systems, including Windows, Linux, and Mac, which makes it versatile for various IT environments.

Security is a paramount consideration for any organization dealing with sensitive data. The Minicom 116 IP incorporates advanced security features, including user authentication protocols and encryption mechanisms. This ensures that only authorized personnel can access the systems, reducing the likelihood of data breaches and unauthorized access.

Moreover, the device is equipped with hot-plugging capabilities, allowing users to add or remove servers without needing to power down the system. This feature enhances uptime and productivity, as administrators can make changes without disrupting ongoing operations.

In addition to its technical facets, the Minicom 116 IP is designed with user experience in mind. It features a user-friendly interface that simplifies the management of multiple servers, making it easier for IT staff to navigate between different machines.

Finally, the device is built for scalability, allowing organizations to expand their IT infrastructure as they grow. This flexibility means that the Minicom Advanced Systems 116 IP can adapt to increasing demands without necessitating a complete overhaul of existing systems.

In summary, the Minicom Advanced Systems 116 IP presents a suite of advanced features, including high-resolution output, robust security protocols, hot-plugging capabilities, an intuitive user interface, and scalable architecture, making it an ideal solution for modern data center management needs.
Top Page Image Contents