Milan Technology RS485-CF-0x specifications Installation, Operation

Page 2

INSTALLATION

Set Switches

Use small flatblade screwdriver or similar device to set recessed switches according to site installation.

1.Set the 2-wire /4-wire slide switch to the 4-wire setting to enable the "receive – RS485 4 wire, RS422 and receive + RS485 4 wire, RS422" pair for RS422 4 wire full duplex operation.

2.Set the RS-485/RS-422 slide switch to the RS-485 position to prevent echo in two-wire mode. Set the RS-485/RS-422 slide switch to the RS- 422 to allow transmit only on "transmit/receive - (B) RS-485 2wire, transmit - RS-422 and transmit/receive + (A) RS-485 2wire, transmit + RS-422" pair.

DOWN=ON Inserts 130 resistor on "receive"*

DOWN=ON Inserts 130 resistor on "transmit"**

DOWN=ON Enables 1K "pull-down"***

DOWN=ON Enables 1K "pull-up"****

 

 

 

 

 

RS-485

RS-422

2-wire

4-wire

1

2

3

4

 

 

 

 

 

 

 

 

-E

 

 

9V

 

 

 

 

 

DC

 

 

 

-100BTX

 

 

Input

 

 

-FX

Config

 

 

 

 

O4

 

Switches

 

 

 

 

MDI MDI-X

1 2 3 4

 

 

 

3.Refer to drawing and to notes below for setting 4-position DIP switch.

*Position 1 ON inserts 130 ohm terminator on the "receive – RS485 4 wire, RS422 and receive + RS485 4 wire, RS422" pair.

**Position 2 ON inserts 130 ohm terminator on the "transmit/receive -

(B) RS485 2wire, transmit - RS422 and transmit/receive + (A) RS485 2wire, transmit + RS422" pair.

***Position 3 ON enables 1K ohm pull down on "transmit/receive - (B) RS485 2wire, transmit - RS422".

****Position 4 ON enables 1K ohm pull up on "transmit/receive + (A) RS485 2wire, transmit + RS422

Install Cable

COPPER /DB-9 CONNECTOR

NOTE: Shielded cables are required on the DB-9 for EMC compliance.

1.Locate or build TIA/EIA-574-DB-9 compliant cables configured as shown on page 6, with a male DB-9 connector at one end of cable and with a straight-through cable.

2.Connect the male DB-9 connector at one end of cable to the Media Converter female DB-9 connector.

3.Connect the other end of cable to the node device.

INSTALLATION -- Continued

COPPER /TERMINAL BLOCK CONNECTOR

1.Locate or build TIA/EIA-574-compliant terminal block cables configured as shown on page 6 and with straight-through cable.

2.Using a small flatblade screwdriver or a similar device, release each terminal block installation location as necessary. Refer to the diagram on page 6, connect the wires at one end of cable to the Media Converter terminal block connector.

3.Connect the other end of the cable to the node device.

FIBER

1.Locate or build TIA/EIA-574-compliant fiber cable with male two- stranded TX to RX connectors at both ends.

TX

TX

RX

RX

2.Connect the male TX and RX cable connectors at one end of the cable to the TX and RX female connectors, respectively, on the Media Converter.

3.Connect the male TX and RX cable connectors at the other end of the cable to the RX and TX connectors of the IEEE 802.3™ compliant fiber device.

Connect to Power

1.Install the power adapter cord at the back of the Media Converter.

2.Connect the power adapter plug to AC power.

3.Verify that the Media Converter is powered by observing the illuminated LED(s).

OPERATION

After installation, the Media Converter should function without operator intervention.

Status LEDs:

Use the status LEDs to monitor Media Converter operation in the network.

RXF Flashing LED indicates data reception on the fiber link.

RXC Flashing LED indicates data reception on the copper link.

P(o)W(e)R Steady LED indicates connection to external power.

RXF

RXC

PWR

3

4

RS485-CF-0x

Image 2
Contents USER’S Guide Installation OperationRS-485/422 Copper Cable Cable SpecificationsFiber Cable Technical Specifications Compliance Information