Operation

Your new CAD Xciter integrated amplifier is ready for operation after the AC power, speaker,

and interconnect cables and the vacuum tubes have been installed into their proper sockets. Refer to the labeling on the chassis for placement and proper tube installation. Since the amplifier circuitry is completely auto-biasing, no biasing adjustments are required – just plug and play!

AC POWER REQUIREMENTS

The CAD Xciter is designed to work from house current AC mains. The design voltage is 120

Volts AC at 50/60 Hz (Foreign units 240 Volts AC at 50/60 Hz). Plug the provided AC power cable into the AC Power jack on the rear panel of the unit.

SOURCE INPUTS

The CAD Xciter accepts 3 unbalanced stereo inputs via the RCA jacks on the rear panel.

Nominal input impedance is 100K Ohm and provides compatibility with common sources such as CD/DVD players, DAC, Cinema, Tuner, and Tape. A shielded high quality interconnect cable is important to reduce chances for hum or interference. Ask your Authorized Cary Audio Design dealer for advice.

SUBWOOFER OUTPUTS

The CAD Xciter provides buffered low level outputs of the selected stereo source input via the

RCA jacks on the rear panel suitable for driving the low level input of amplified subwoofers. A shielded high quality interconnect cable is important to reduce chances for hum or interference. Ask your Authorized Cary Audio Design dealer for advice.

SPEAKER BINDING POSTS

The CAD Xciter will drive loudspeaker loads from as low as 4 ohms to a high of 16 ohms

without any adjustments. Please remember to keep the proper phase on each channel when connecting the loudspeaker cables. Red is the positive and black is the negative lead. The positive binding post (on both left and right channels) is located closest to the middle of the chassis. Check your speaker cables periodically to make sure the connections are tight.

POWER ON / OFF SWITCH

The AC Power rocker switch for power on - power off is located in the lower left-hand corner of the front panel. The CAD Xciter becomes fully operational once the AC Power cord is plugged

into the unit and into the wall AC outlet the Power On/Off switch is turned On. Push the “1” at the top of the switch to turn the unit on. You will notice that blue back lighting behind the Listening Level control on the front panel will illuminate. The vacuum tubes will light as well. Blue LEDs will also illuminate the base of each 12AX7A tube. The unit is powered down (turned off) simply by pushing the “0” at the bottom of the power switch. AC power is then removed from the power supply in the CAD Xciter.

Xciter specifications

Cary Audio Design has long been synonymous with high-quality audio equipment, and their latest offering, the Xciter, is no exception. This advanced audio amplifier brilliantly combines cutting-edge technology with timeless design, making it a standout in any audiophile's setup.

One of the most notable features of the Xciter is its hybrid design, incorporating both solid-state and tube technology. This unique combination allows the amplifier to deliver a warm, rich sound characteristic of tube amplifiers while benefiting from the speed and precision of solid-state components. This synergy results in an audio experience that is both immersive and nuanced, perfect for critical listening sessions or casual enjoyment.

The Xciter boasts an impressive power output, capable of driving a wide range of speakers with ease. With an output of 125 watts per channel into 8 ohms, and even more at lower impedances, the Xciter can handle demanding music genres and maintain clarity without distortion. Cary Audio has also ensured that the amplifier provides ample headroom, allowing listeners to enjoy musical peaks without compromising fidelity.

Another key aspect of the Xciter is its advanced circuitry. The amplifier features a fully balanced design, which minimizes noise and increases detail in the audio signal. Additionally, Cary Audio has implemented high-quality components and meticulous circuit layout, ensuring that every note is rendered with precision and authenticity. The power supply is robust, providing stable energy to the amplifier for optimal performance.

User convenience is also a priority with the Xciter. The amplifier is equipped with a smart, intuitive control interface, allowing users to switch between various input sources seamlessly. Additionally, it features remote control access for easy adjustments from the listening position, enhancing the overall user experience.

Cary Audio Design has not overlooked aesthetics either. The Xciter showcases a sleek, modern design with a beautiful brushed aluminum finish and warm LED illumination. It is a piece of art that complements any decor while signifying the quality and sophistication of the audio equipment within.

In conclusion, the Cary Audio Design Xciter is a remarkable achievement in the world of audio amplification. With its hybrid technology, powerful output, advanced circuitry, user-friendly features, and stunning aesthetics, it stands as a testament to Cary Audio’s dedication to enhancing the listening experience. Audiophiles looking for a versatile and high-performing amplifier will find the Xciter to be a worthy addition to their audio arsenal.