McDATA 4314 manual Connect the Management Workstation to the Switch Module

Page 37

Installing a Switch

3.After approximately one minute, the POST executes.

4.After about another minute, the POST is complete, all LEDs are extinguished except the Input Power LED. The Input Power LED remains illuminated indicating that the switch logic circuitry is receiving DC voltage. If not, contact your authorized maintenance provider.

Connect the Management Workstation to the Switch Module

Connect the management workstation to the switch module in the following ways:

Indirect Ethernet connection from the management workstation to the switch module RJ-45 Ethernet connector through an Ethernet switch or a hub. This requires a 10/100 Base-T straight cable as shown in Figure 3-2. With this method, you can manage the switch module with the EFCM BASIC application or Command Line Interface.

Direct Ethernet connection from the management workstation to the switch module RJ-45 Ethernet connector. This requires a 10/100 Base-T cross-over cable as shown in Figure 3-2. With this method, you can manage the switch module with the EFCM BASIC application or Command Line Interface.

Indirect Ethernet

Direct Ethernet

RJ-45 Connection

RJ-45 Connection

8

 

1

 

8

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

8

8

 

 

8

7

 

 

 

7

7

 

 

7

6

 

 

 

 

6

6

 

 

6

 

 

 

 

5

 

 

 

5

5

 

 

5

4

 

 

 

4

4

 

 

4

3

 

 

 

 

3

3

 

 

3

 

 

 

 

2

 

 

 

 

2

2

 

 

2

 

 

 

 

1

 

 

 

 

1

1

 

 

1

 

 

 

 

Figure 3-2. Ethernet Cable Connections

The default IP address of a new switch module is 10.0.0.1. Many management workstations are not configured to communicate with the 10.0.0 subnet. Use the EFCM BASIC Configuration Wizard to set the IP address of a new switch without re-configuring the management workstation.

To establish an Ethernet connection, do the following:

1.Connect a 10/100 Base-T cross-over cable from an RJ-45 port on the management workstation directly to the RJ-45 Ethernet port; or a 10/100 Base-T straight cable indirectly over an Ethernet network.

2.Open a command line window.

Installation

3-5

Image 37
Contents McDATA Fibre Channel Switch Module Installation Guide Copyright 2005 McDATA Corporation. All rights reserved Contents Chapter Troubleshooting Chapter InstallationAppendix a Specifications Contents McDATA 4314 Fibre Channel Switch Module Installation Guide Figures Figures Viii Tables Tables Preface How to Use this ManualWho Should Use this Manual Related DocumentationPreface General Description McDATA 4314 Switch ModuleMaintenance Button Switch Module Controls and LEDsFibre Channel Ports Switch Module LEDsExternal Port LEDs Port Logged-In LED Green TransceiversPort Types Ethernet PortMcDATA Embedded Web Server Switch Module ManagementSimple Network Management Protocol Command Line InterfaceFile Transfer Protocol Devices PlanningSoft Zones Device AccessAccess Control List Hard Zones Distance PerformanceBandwidth Latency Optimizing Device Performance Multiple Chassis FabricsDomain ID, Principal Priority, and Domain ID Lock Switch Module Services Fabric Security Connection Security Device Security User Account Security Fabric ManagementSite Requirements InstallationFabric Management Workstation Site Requirements Install SFP Transceivers Installing a SwitchEnvironmental Conditions Mounting the Switch Module in the Server Chassis Mount the Switch Module in the Server ChassisIndirect Ethernet Direct Ethernet RJ-45 Connection Connect the Management Workstation to the Switch ModuleFor a Windows platform Install Efcm BasicStart Efcm Basic Configure the Switch Module Cable Devices to the Switch Using Efcm Basic to Install Firmware Install FirmwareUsing the CLI to Install Firmware Password required for johndoe. Password User johndoe logged McDATA 4314 Fibre Channel Switch Module Installation Guide Input Power LED Is Extinguished TroubleshootingSystem Fault LED is Illuminated EPort Isolation Logged-In LED IndicationsExcessive Port Errors Recovering a Switch Module Maintenance Exit Maintenance Reset Network Config Maintenance Image UnpackMaintenance Reset User Accounts to Default Maintenance Copy Log FilesMaintenance Reset Switch Maintenance Remake FilesystemMaintenance Update Boot Loader McDATA 4314 Fibre Channel Switch Module Installation Guide Fabric Specifications SpecificationsLED indicators Maintainability SpecificationsDimensional Specifications Fabric Management SpecificationsElectrical Specifications Environmental Specifications Certification Description Regulatory CertificationsMcDATA 4314 Fibre Channel Switch Module Installation Guide Glossary Administrative StateMcDATA 4314 Fibre Channel Switch Module Installation Guide Fdmi MIB Protocol McDATA 4314 Fibre Channel Switch Module Installation Guide Numerics IndexLED Reset 1-2,4-7services 2-8specifications A-1 McDATA 4314 Fibre Channel Switch Module Installation Guide

4314 specifications

The McDATA 4314 is a highly regarded Fibre Channel switch designed for enterprise storage area networks (SANs). This switch is particularly known for its reliability, high performance, and scalability. As part of McDATA's extensive range of networking products, the 4314 stands out for its ability to meet the demands of modern data centers, providing seamless connectivity for numerous storage and server devices.

One of the main features of the McDATA 4314 is its robust architecture, which supports up to 32 ports. This enables a flexible configuration that can easily scale as the needs of the organization grow. The switch is characterized by its ability to handle both FC-AL and FC-SW protocols, thus providing compatibility with a wide range of existing Fibre Channel devices. This versatility makes it ideal for organizations looking to enhance their existing infrastructure without the need for a complete overhaul.

In terms of performance, the McDATA 4314 supports high bandwidth requirements, with each port capable of delivering up to 4 Gbps. This high throughput is critical for data-intensive applications, ensuring low latency access to data stored on SAN devices. Additionally, the switch incorporates advanced technologies such as dynamic load balancing and intelligent pathing, which further optimize traffic flow and enhance overall system performance.

Security is a key consideration in any data center environment, and the McDATA 4314 addresses this with features such as zoning and masking. These capabilities ensure that only authorized devices can access specific data, safeguarding sensitive information from potential breaches. Moreover, the switch supports management protocols like SNMP (Simple Network Management Protocol), allowing for seamless integration into existing network management systems and enabling administrators to monitor performance and troubleshoot efficiently.

In terms of characteristics, the McDATA 4314 is designed for high availability, with redundant components that minimize downtime in critical environments. Furthermore, its compact form factor allows for efficient rack space utilization, making it a practical choice for organizations with space constraints.

Overall, the McDATA 4314 Fibre Channel switch provides a combination of performance, reliability, and scalability, making it an ideal choice for enterprise environments. Its advanced features and robust design ensure that organizations can maintain high levels of performance while effectively managing their storage networks. Whether supporting virtualized environments or managing extensive data storage, the McDATA 4314 is a valuable asset for any data center infrastructure.