Bryston B100 Integrated Amplifier Manual: Features & Setup Guide

B100 TWO CHANNEL POWER AMPLIFIER

INTRODUCTION:

Thank you for purchasing a Bryston B100 integrated amplifier. We are confident it will provide you with many years of musical enjoyment. We would welcome any suggestions or comments you may have regarding the operation of your Bryston amplifier.

In the unlikely event that your amplifier may require service Bryston recommends that you retain the original shipping box and packaging material for future use if required.

SETUP RECOMMENDATIONS:

You may place your B100 integrated amplifier in any convenient location. Make sure you position the ampli- fier to maintain a direct line-of-sight between the hand-held remote and the remote sensor eye located on the front panel. If plugged in the B100 will remain in standby indicated by the RED power LED on the front panel.

The amplifier is powered up by engaging the power button located on the front panel of the B100 or by depressing the POWER button on the hand held remote control unit.. The B100 will power-up momentarily with mute engaged, indicated by the mute LED turning red on the front panel; it will then turn off within a few seconds. The POWER LED will stay lit green indicating normal operation.

CONNECTIONS:

LOUDSPEAKERS:

Connect your loudspeakers, ensuring that the positive (red) and ground (black) terminals (gold-plated 5-way binding posts) on the Bryston B100 integrated amplifier are connected to the positive and ground terminals on your loudspeakers. Make certain the left and right speaker outputs on the amplifier are connected to your appropriate left and right loudspeakers.

SEPARATE PRE-AMP OUT & POWER AMP IN JACKS:

These two pair of RCA jacks allow for the independent use of the stereo amplifier section within a multi-chan- nel audio or video system. On the rear panel there are connections labeled ‘PRE AMP OUT’ (preamplifier output) and ‘POWER AMP IN’ (power amplifier input) along with two slide switches (one per channel) labeled “Separate/Connect”. This feature allows you to "separate or connect" the preamplifier section of the B100 from the power amplifier section thus producing a separate stereo preamp and separate stereo power amplifier.

WIRED (SERIAL DATA) REMOTE CONTROL:

There is one RS-232, one AUX IR input and two 12 volt trigger output connections as well. The RS-232 is bi- directional and allows for future software downloads from the Bryston website. It also interfaces with control systems such as Crestron and AMX.

CHASSIS GROUND:

A chassis ground thumb screw terminal is provided on the rear panel.

12 VOLT TRIGGER CONNECTOR:

These 12Vdc control outputs allow the B100 to exert on/off control over compatible equipment. See “REMOTE POWER CONTROL” for more information..

LINE LEVEL ANALOG AUDIO INPUTS :

The Bryston B100 integrated amplifier comes equipped with 8 pairs of gold plated analog RCA input con-

nectors: TV, CD, AUX-1/PHONO,AUX-2/SPDIF,VIDEO, TUNER, RECORD IN and POWER AMP IN. All have and input impedance of 50K ohms

• Power Amp In is normally connected, internally, to Pre Amp Out via the Connected/Separate slide switch located on the rear panel. When this switch is in the Separate position, however, any line level audio input can be used at the Power Amp Input jacks to drive the amplifier.

• In B100-DA models the Aux2 (d1/d2) input jacks accept only SPDIF PCM bit streams. They do NOT accept

B100-DA, B100-P specifications

The Bryston B100-P and B100-DA are stellar entries in the high-end audio market, combining advanced technologies with sophisticated design. Known for their unwavering commitment to sound quality, Bryston amplifiers are often the choice of serious audiophiles and professionals alike.

The B100-P is a powerhouse integrated amplifier that boasts an impressive output of 120 watts per channel into an 8-ohm load, ensuring that it can drive a wide range of loudspeakers with ease. It features both balanced and unbalanced inputs, making it versatile for various setups. The B100-P incorporates Bryston's renowned technology, including a low-noise power supply and high-quality components that minimize distortion and enhance audio fidelity.

One of the standout characteristics of the B100-P is its build quality. It features a robust aluminum chassis, designed to minimize resonance and electromagnetic interference, thereby preserving the sonic integrity of the music. Additionally, the amplifier is equipped with a toroidal transformer, which contributes to efficient power delivery and ensures a dynamic response across different frequencies.

On the other hand, the B100-DA elevates the integrated amplifier experience by incorporating a high-resolution digital-to-analog converter (DAC). This model supports a variety of digital inputs, including USB, coaxial, and optical, allowing users to connect a diverse array of digital sources easily. The DAC section utilizes premium-grade chips to provide outstanding clarity and detail in the audio signal. The B100-DA is capable of decoding high-resolution audio formats, ensuring that the user can enjoy a superior listening experience, whether it be from high-quality streaming services or local file storage.

Both models come equipped with a full-function remote control, making it easy to navigate through different inputs and settings. The user interface is intuitive, providing quick access to adjustments without complex menus. Additionally, the B100 series features a 20-year warranty, underscoring Bryston’s confidence in their product's durability and performance.

In summary, the Bryston B100-P and B100-DA not only deliver exceptional sound quality but also integrate cutting-edge technologies that cater to modern audiophiles. Whether you choose the versatile B100-P or the advanced B100-DA with its digital connectivity, both amplifiers promise to enhance any high-fidelity audio setup. With their stellar reputation and commitment to excellence, Bryston continues to be a leader in the audio industry, offering products that resonate with passion and precision.