ADVANCED OPERATION
All On/All Off
The WS15Z-1 supports the ALL ON/ALL OFF commands.
The WS15Z-1 can be set to respond to ALL ON and ALL OFF commands four different ways.
Refer to your controller for information on how to set the WS15Z-1 to operate in the manner you desire. Some controllers may be only able to set certain settings of ALL ON/ALL OFF response.
The four different ways the WS15Z-1 can be setup to respond to ALL ON and ALL OFF commands are:
1.WS15Z-1 will not respond to ALL ON or the ALL OFF command.
2.WS15Z-1 will respond to ALL OFF command but will not respond to ALL ON command
3.WS15Z-1 will respond to ALL ON command but will not respond to ALL OFF command.
4.WS15Z-1 will respond to ALL ON and the ALL OFF command.
CONFIGURATION
The WS15Z-1 supports the Configuration command.
The WS15Z-1 can be confi gured to operate slightly differently than how it works when you fi rst install it. Using the Confi guration command you can confi gure the following:
Night Light
By default, the LED on the WS15Z-1 will turn OFF when the load attached is turned ON. To make the LED turn ON when the load attached is turned ON, set parameter 3 to a value of 0.
•Parameter No: 3
•Length: 1 Byte
•Valid Values = 0 or 1 (default 1) Invert Switch
To change the top of the switch to OFF and the bottom of the switch ON, set parameter 4 to 1.
•Parameter No: 4
•Length: 1 Byte
•Valid Values = 0 or 1 (default 0)
Each confi guration Parameter can be set to its default setting by setting the default bit in the Confi guration Set command. See your controller’s instructions on how to do this (and if it supports it).
All confi guration commands will be reset to their default state when the WS15Z-1 is excluded from the Z-Wave network by using the controller to reset the node.
SPECIFICATIONS
Power | 120 VAC, 60 Hz |
Signal | (Frequency) 908.42 MHz, 9.6Kbps or 40Kbps capable |
Maximum Load: Resistive: 15 amps (1800 watts) maximum, 120 VAC Motor: 1/2 H.P. maximum, 120 VAC Incandescent: 600W maximum, 120 VAC
Range: Up to 100 feet line of sight between the Wireless Controller and/or the closest HomePro Receiver Module
INTEROPERABILITY WITH Z-WAVE DEVICES
A Z-Wave™ network can integrate devices of various classes, and these devices can be made by different manufacturers. just as the WS15Z-1 can be incorporated into existing Z-Wave™ networks. The top or bottom of the WS15Z-1 switch paddle can be used to carry out inclusion (inclusion to the network by adding to a group), association (operate simultaneously with other nodes), exclusion (remove from a group) or reset (remove from the network). Controllers can be replicated in order to provide operation from other locations.
REGULATORY INFORMATION
The WS15Z-1 is certifi ed to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
FCC NOTICE
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician to help.
•Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
IC NOTICE
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes
:(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve
(12)months. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of
Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until Warranty Expiration Date as labeled on the product. This
Linear LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
IMPORTANT !
Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless signaling. However, there are some limitations which must be observed.
•For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.
•A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.
•Changes or modifications to the device may void FCC compliance.
•Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
•A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.
