Heath Zenith SL-5412 manual Installation, Eave Mount Wall Mount, Wire the Light Control

Page 2

 

 

INSTALLATION

Mounting

For easy installation, select an existing light with a wall

Strap

switch for replacement.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Black to Black

White to White

Rubber

Plug

Eave Mount

Wall Mount

For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock.

For eave mount only:

Swing the sensor head towards the clamp screw

joint.Controls Clamp

Screw

23456789012345678

Then rotate the sensor head clockwise 180° so the controls face down.

Controls

Controls

If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done.

WIRE THE LIGHT CONTROL.

Turn power off at the fuse or circuit breaker.

Remove the existing light fixture.

Install the mounting strap as shown using two screws that fit your junction box.

The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap.

Route the Light Control’s wires through the large gasket holes.

Twist the junction box wires and fixture wires together as shown. Secure with wire connectors.

Mounting

Bolt

Gasket

Junction box ground wire to green ground screw on fixture.

MOUNT THE LIGHT CONTROL.

Align the Light Control cover plate and cover plate gasket. Secure with the mounting bolt.

Align the three slots in the decorative shell with the lamp holder pins. Push the shell in and then twist clockwise to lock. Repeat for other shell.

Shell Slot

Push the Rubber Plug firmly into place.

If a wet location junction box was not used, caulk the wall plate mounting surface with silicone weather sealant.

To avoid water damage and electrical shock, keep lamp holders 30° below horizontal.

 

Keep lamps at least

 

1" (2.5 cm) from the

 

sensor. Do not al-

Lock Nut

low the lamps to

block the lens.

 

Lens

 

Adjust the lamp holders by loosening the lock nuts but do not rotate the lamp holders more than 180° from the factory setting. When screwing in the floodlamps, do not overtighten.

2

595-5767-02

Image 2
Contents Model SL-5412 FeaturesOperation RequirementsEave Mount Wall Mount InstallationWire the Light Control Mount the Light ControlTurn on the circuit breaker and light switch Test and AdjustmentSpecifications Avoid aiming the control atSymptom Possible Cause Troubleshooting GuideIf you experience a problem, follow this guide Modèle SL-5412 Résumé du mode de commutationFonctionnement CaractéristiquesMontage sous avant-toit Montage DE LA Commande D’ÉCLAIRAGECâblage DE LA Commande D’ÉCLAIRAGE Montage muralEssais ET Réglages Fiche TechniqueSymptôme Cause Possible Guide DE DépannageSi vous éprouvez des difficultés, suivre ce guide
Related manuals
Manual 12 pages 19.35 Kb

SL-5412 specifications

The Heath Zenith SL-5412 is a remarkable piece of technology in the realm of outdoor lighting and security solutions. With its blend of aesthetic design and advanced functionality, this motion sensor light fixture has become a popular choice for homeowners seeking to enhance their exterior spaces.

One of the standout features of the SL-5412 is its dual-lens motion sensing technology, which is designed to detect movement with impressive accuracy. The dual passive infrared sensors work simultaneously to cover a vast area, significantly reducing the chances of false alarms that can occur with single-sensor systems. This technology allows the fixture to be adjustable, providing a customizable experience that can suit various outdoor settings.

The SL-5412 also boasts a powerful LED light source, which delivers bright illumination while being energy-efficient. The fixture typically generates a lumen output that provides excellent visibility for any outdoor area, enhancing safety and security around the home. Additionally, LED bulbs have a longer lifespan compared to traditional incandescent bulbs, reducing the frequency and cost of replacement.

A key characteristic of the Heath Zenith SL-5412 is its weather-resistant construction. Built to withstand diverse weather conditions, the fixture is ideal for outdoor use, ensuring durability and reliability in any climate. Its rugged design not only protects it from rain and wind but also contributes to long-term maintenance-free operation.

The adaptability of the SL-5412 is further highlighted by its adjustable settings. Users can easily modify the sensitivity of the motion sensors, the duration of light activation, and the ambient light threshold, allowing for precise control over the unit’s performance in response to surrounding conditions.

Another notable aspect of this security light is its sleek design, which blends seamlessly with most home exteriors. Available in multiple finishes, the SL-5412 enhances the aesthetic appeal of outdoor spaces while serving its primary purpose of providing safety and visibility.

In summary, the Heath Zenith SL-5412 combines modern technology with thoughtful design features to create a versatile solution for outdoor lighting and security. Its dual-lens sensing technology, energy-efficient LED output, weather-resistant durability, and customizable settings make it an exceptional choice for any homeowner looking to improve their outdoor environment. As security and efficiency continue to be a priority in home improvement, the SL-5412 stands out as a reliable and effective option.