HomeTech 41108-R*8, 41106-R*6 manual QuickPort Usoc Snap-in Connector, Instructions for Use

41106-R*6

41108-R*8

41106-R*6

41108-R*8

QuickPort® USOC Snap-in Connector

Instructions for Use

QuickPort® USOC Snap-In Connector

DESCRIPTION

Leviton’s QuickPort USOC Snap-In Connectors feature a wiring configuration label for quick and easy wiring.

QuickPort® USOC Snap-in Connector

Instructions for Use

QuickPort® USOC Snap-In Connector

DESCRIPTION

Leviton’s QuickPort USOC Snap-In Connectors feature a wiring configuration label for quick and easy wiring.

INSTALLATION

1.Remove jacket from cable.

Pin				2.	Check jack termination label (located on sides of
Number
					jack) for wiring standard and associated color codes.
					The label also includes jack pin numbers. (Figure 1)
4	5	6		3.	Route the wires for termination as shown in
					Figure 2.
Color Code for			1	4.	Using a 110-style punchdown tool, seat the wires into
USOC Wiring					the IDC slots. With the cutting edge of the tool to the
					outside, trim the excess wire flush with the jack body.
					(Figure 3)
				NOTE: Brown pair of UTP not used for this connector.
				5.	Place the cap over the termination wires for secure
					connection and added strain relief. (Figure 4)
				6.	Insert jack assembly into platform or wallplate. Note
					the “UP” position of the jack.
			2	IMPORTANT INSTRUCTIONS
				1. Read and understand all instructions. Follow all warnings and
					instructions marked on the product.

2.Do not use this product near water—e.g., near a tub, wash basin, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

3.Never push objects of any kind into this product through openings, as they may touch dangerous voltages.

	4.	SAVE THESE INSTRUCTIONS.
3	SAFETY INFORMATION
	1.	Never install communications wiring or components during a
	2.	lightning storm.
		Never install communications components in wet locations
		unless the components are designed specifically for use in wet	00A-41106-C00-DI
	3.	locations.
		Never touch uninsulated wires or terminals unless the wiring has
	4.	been disconnected at the network interface.
		Use caution when installing or modifying communications wiring
4	5.	or components.
		To prevent electrical shock, each opening must be filled with a
		module.

2222 - 222nd Street SE

Bothell, WA 98021, USA

Phone: (425) 485-4288

Fax: (425) 483-5270

INSTALLATION

1.Remove jacket from cable.

Pin			2.	Check jack termination label (located on sides of
Number
				jack) for wiring standard and associated color codes.
				The label also includes jack pin numbers. (Figure 1)
4	5	6	3.	Route the wires for termination as shown in
				Figure 2.
Color Code for			4.	Using a 110-style punchdown tool, seat the wires into
USOC Wiring			1	the IDC slots. With the cutting edge of the tool to the
				outside, trim the excess wire flush with the jack body.
				(Figure 3)
			NOTE: Brown pair of UTP not used for this connector.
			5.	Place the cap over the termination wires for secure
				connection and added strain relief. (Figure 4)
			6.	Insert jack assembly into platform or wallplate. Note
				the “UP” position of the jack.
			2
			IMPORTANT INSTRUCTIONS
			1. Read and understand all instructions. Follow all warnings and
				instructions marked on the product.
			2. Do not use this product near water—e.g., near a tub, wash basin,
				kitchen sink or laundry tub, in a wet basement, or near a
				swimming pool.

3.Never push objects of any kind into this product through openings, as they may touch dangerous voltages.

	4.	SAVE THESE INSTRUCTIONS.
3	SAFETY INFORMATION
	1.	Never install communications wiring or components during a
	2.	lightning storm.
		Never install communications components in wet locations
		unless the components are designed specifically for use in wet	00A-41106-C00-DI
	3.	locations.
		Never touch uninsulated wires or terminals unless the wiring has
	4.	been disconnected at the network interface.
		Use caution when installing or modifying communications wiring
4	5.	or components.
		To prevent electrical shock, each opening must be filled with a
		module.

2222 - 222nd Street SE

Bothell, WA 98021, USA

Phone: (425) 485-4288

Fax: (425) 483-5270