GE manual Installation, Selecting a Site for the Switch, Methods for Mounting the D-GES7600

Page 16

Manageable 8/9-Port Switch

INSTALLATION

This section gives step-by-step instructions about how to install the EtherNav” D-GES7600 switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch where it will not be subjected to temperatures, humidity, or electromagnetic interference above the rated specifications. The site you select should meet the following requirements:

-The ambient temperature should be between –40 to 74 degrees Celsius.

-The relative humidity should be less than 95 percent, non-condensing.

-Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for EIC 801-3, Level 2 (3V/M) field strength.

-Make sure that the switch receives adequate ventilation. Avoid blocking the ventilation holes on all sides of the switch.

Methods for Mounting the D-GES7600

Several mounting configurations are available for the variety of applications for which this switch was designed. Each configuration is described as follows:

Wall or Floor Mounting (-W Option)

The brackets provided will require the removal and re-installation of the cover screws as shown below.

Bracket

(-W Option)

Cover Screws

Note: Insure that all screw are re-installed for adequate stability in mounting.

12

User’s Manual

Image 16

Contents Managed ethernet switches Preface Preface Table of Contents Product Overview Switch Management … SNMP-Based Network ManagementProduct Features Package ContentsProduct Overview Vlan Power Indicator Front Panel DisplayOptical Status LED’s FX 10/100/1000TX Port Status LED’sPhysical Ports Mode SelectionConnectivity Unicast Switching Basic FunctionsPlease Note Vlan Classification Learning Filtering AgingForwarding Multicast Switching Spanning TreeVlan Broadcast Control MULTICAST-BASED Multimedia ApplicationsImproved Security Vlan MembershipVlan Configuration Igmp Snooping and IP Multicast FilteringRemote Vlan Membership INTRA-VLAN CommunicationSwitch Management Administration Console Via RS-232 Console PortWeb-Based Browser Interface External SNMP-Based Network ManagementInstallation Selecting a Site for the SwitchMethods for Mounting the D-GES7600 Wall or Floor Mounting -W OptionDIN Rail Back Mounting -DB Option DIN Rail Side Mounting -DS OptionRack Mounting Single Unit -RS Option Rack Mounting Dual Units -RD Option External Power Connecting to PowerPower-On Self Test Post Connecting to Your Network Cable SpecificationsCable Type & Length CablingManagement Access Overview Advantages External SNMP-Based Network Management ApplicationAdministration Console Direct AccessDefault Parameters Telnet AccessNetscape Navigator WEB ManagementInternet Explorer SNMP-BASED Network Management ProtocolsVirtual Terminal Protocols, such as Telnet Simple Network Management Protocol SnmpLogging On To The Switch Login NamePassword Factory Default Password ethernav, press Enter directlySwitch Management Screen Performing Basic Management Activities Navigating Through the Console InterfaceGeneral Management Configurations StepAdmin Password Guest PasswordReboot-on-Error Remote Telnet LoginManageable 8/9-Port Switch Flow Control Physical Port Address Admin. ControlReturn to Basic Management Manageable 8/9-Port Switch Alarm Configurations Step Performing Advanced Management Activities SnmpCreate Vlan Manageable 8/9-Port Switch Delete Vlan Press enter View or search by MAC address individually Per Port Statistics Per Port MAC Unit Manageable 8/9-Port Switch Manageable 8/9-Port Switch Ping Settings Step Timeout sec HostCount Size bytesAging Time Bridging StepFlood Limits for all Ports Source/Destination MAC Address Out-Filters MAC Address in Filters Add/Delete/Search Spanning Tree Protocol Bridge PriorityHello Time sec Press enterForward Delay sec Max Age secSpanning Tree Port States Step Spanning Tree Path Costs StepSpanning Tree Port Priorities Step Protocol MigrationEdge Port Point-to-Point Link Snmp Functions Step Snmp OptionsRising Alarm Trap Falling Alarm TrapGet Community Name Set Community NameIgmp Select Actor or Partner for the Port selected Actor Screen Partner Screen Aggregation Port Settings Step Fast Link Aggregation Step Manageable 8/9-Port Switch Quality of Service QoS Step Mirror ModeGlobal Setting Step Logical Port Step ToS Set Queue for optional Port Sending and Receiving Files Send File Via Tftp Step Repeat StepSwitch Management, and press enter Logging on to the Switch Switch IP AddressLogin ID WEB-BASED Browser ManagementBasic Setup Advanced SetupUnderstanding the Browser Interface FileSaving Setting Performing File ActivitiesTo Perform File Activities Step Click Receive NowTo perform Basic Setup Activities Performing Basic Setup ActivitiesGeneral Management Configuration LAN Port Configuration Step Statistic CollectionPort Setting Port StatusManageable 8/9-Port Switch Basic Setup/Console Port Configuration Console Port Configuration StepModem Control Modem Setup String Flag Step Performing Advanced Setup Activities To Perform Advanced Setup ActivitiesMAC Address Management Step Per Vlan ViewIndividual MAC View Per Port ViewMAC Address Management. Click Individual MAC View Step Specify whether you want to advertise routes Per Port Statistics Step Port Priority StepAging Options Static MAC FilterDestination MAC Address IP Multicast GroupVlan Configuration Click Vlan Configuration Step Add a Vlan EntryDelete a Vlan Entry Step Delete a Vlan Entry window appearsAggregation Port Status Port Settings Step Community Name value is public Snmp Topology Alarm Trap Authentication Failure TrapUpdate Setting Port Mirroring Overview Snmp & Rmon ManagementSnmp Agent and MIB-2 RFC Rmon MIB RFC 1757 and Bridge MIB RFC Rmon Groups SupportedBridge Groups Supported Specifications Appendix a Connector Pinouts Limited Warranty GE Security