GE PSB1200NBB/WW dimensions Prepare the opening, Single Oven Installation

PSB1200NBB/WW

GE Profile Advantium® 120 Volt - 30" Wall Oven

Preparation with an Accessory Drawer

Prepare the opening

The Advantium PSB1200/1 series can be installed in combination with other GE/Monogram appliances. Always follow each product's Installation Instructions to compete the installation.

Single Oven Installation:

Order a 30" wide single oven cabinet or cut the opening in a wall to the dimensions shown.

			23-1/2”
* For existing cutouts, a maximum width	30”
of 28-1/2" is acceptable. If the opening
is slightly wider, secure a furring strip
			25-1/4”
on each side of the cutout for securing			Min.
the oven.
• Allow 3/4" to 2-1/8" case trim overlap
		21”
on the sides and 7/8" overlap on the				Construct

Prepare the opening (cont.)

When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium and the other appliance overlaps. Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides.

•the support must be level and rigidly mounted, flush with the bottom edge of the cutout.

Installation over a GE/Monogram Oven and Warming Drawer:

			Construct Solid
	30”	23-1/2”	Bottom Min.
			3/8” Plywood
			Supported by
			2x4 or 2x2
		25-1/4”	Runners all
			Four Sides
		Min.
		21”	2” Min.
			(3” recommended)
			Per Oven
			Requirement
5” min.
from floor			2” Min.
1” min.
above	Per warming drawer requirement
toekick

bottom of the opening for all models.		Base
		Min. 3/8”
The amount of overlap on the sides	5” min.	Plywood
	from floor	Supported
depends on the actual cutout width.		by 2x4 or 2x2
	1” min.
		Runners all
Allow 1-1/4" case trim overlap on the	above	Four Sides
top for models PSB1200 and PSB1201	toekick
and for models ZSC1201 and ZSC1202.

• Oven overlaps will conceal cut edges on all sides of the opening.

Note: PSB1200/1 series Advantium can be installed below GE/GE Profile non-downdraft gas and electric cooktops. It CANNOT be installed below induction or Monogram (2GU3841385) gas cooktops.

Note: PSB1200/1 series Advantium oven comes with two lower trim pieces. One is for use above 36-inch height installations and one is for use below 36-inch installations. Use of the accessory drawer will replace the bottom trim piece for applicable installations. Please see

30”

21”

5” min. from floor 1” min. above toekick

	23-1/2”	Construct
		Solid Bottom
		Min. 3/8”
		Plywood
		Supported
25-1/4”		by 2x4 or 2x2
Min.		Runners all
		Four Sides
			2” Min.
			(3” recommended)
				Per warming
				drawer
				requirement

Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.

Caution: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this approximate 80-pound oven and 30- pound drawer, plus additional oven loads of up to 50 pounds or a total weight of 160 pounds.

installation instructions for full details.

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.

Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.

Listed by Underwriters Laboratories

Specification Created 11/08 240445